PURGE CHUTE COVER WITH SILICON NOZZLE WIPER by Engineering Projects

Engineering Projects

3D Printer>3D Printer Parts

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

STANDARD

Designer

25 min

1 plate

4.6(108)

STANDARD WITHOUT LOGO

Designer

21 min

1 plate

4.6(77)

Boost

588

1298

374

1.8 k

1.3 k

Released

Description

NOTICE: REMIX ARE NOT ALLOWED

NOTICE: DO NOT POST ANY OF YOUR PROFILE

I design this a purge chute cover with a silicon nozzle wiper.

Benefits:

Purged filament doesn't jump on the plate
Nozzle is better cleaned
Pieces of purged filament don't go everywhere , each corner of the printer remains clean

How to install THE MODELS WITH and WITHOUT THE LOGO:

How it works:

INSTRUCTIONS

What is the nozzle wiper made of?

It is made from a piece of silicone from the molds used to make pancakes. Like this one you see in this pic:

How big should the silicone piece to be cut be?

10mm x 2mm x 15mm

PRINT THE POOP STOP WITH THE NOZZLE WIPER

CUT THE PIECE:

APPLY THE SILICON PIECE IN THE SEAT OF THE POOP STOP AND INSTALL THE POOP STOP IN THE POOP BUCKET

AS YOU SEE IN THIS PIC , MY MODEL IS SUPER FLAT, SO WARPING MUST BE ON IT TO AVOID CRASHED OR SCRATCHES AGAINST THE HOTEND, TOOLHEAD OR FAN DUCT:

BE SURE WHEN YOU'RE PRINTING , THE PRINT IS NOT WARPING!!

With what materials should it be printed?

I recommend PAHT-CF and PET-CF. This is because, when the printer is performing the "nozzle cleaning tip" function, the nozzle temperature is 200°C.
So I recommend printing it with materials that resist high temperatures to avoid deformation or future problems.

Do you want to use ABS? Ok, you're free to do so, but don't give me a bad rating for YOUR CHOICE!

I have tested this model so many times and it works smoothly! No issue.

ALL THE MODELS ARE AVAILABLE ON MY PAGE.

NOTICE:

DON'T MODIFY THE ORIENTATION!

NOTICE: THE FOLLOWING PHOTO SHOWS THE EXTRUDED FILAMENT BEING HELD ON THE SILICON NOZZLE WIPER, BEFORE PRINTING.

THIS IS ONE OF THE MAIN REASONS WHY I DESIGNED THIS MODEL. THAT EXTRUDED FILAMENT COULD RUIN YOU FIRST LAYER!

PLEASE CHECK ALWAYS IF THE SILICON NOZZLE WIPER IS CLEAN AND IF YOU SEE THAT SOME EXTRUDED FILAMENT HAS BEEN DEPOSITED ON IT, REMOVE THE EXTRUDED FILAMENT AND ENJOY 3D PRINTING.

THE PHOTO WAS MADE AS EXAMPLE AFTER 3h PRINTING.

MY MODEL HAS ALREADY BEEN TESTED, FOR A MONTH AND I DON'T FIND ANY PROBLEMS.

THE MODEL ,AS TEST EXAMPLE IN THE PIC, WAS PRINTED IN ABS, BUT I STILL RECOMMEND SUPERIOR FILAMENTS LIKE PC , PATH OR PET.

𝙽𝙾𝚃𝙸𝙲𝙴:

𝚃𝙷𝙸𝚂 𝙸𝚂 𝙰 𝚂𝙸𝙼𝙿𝙻𝙴 𝙿𝚁𝙸𝙽𝚃. 𝙰𝚂 𝚈𝙾𝚄 𝚂𝙴𝙴 𝙸𝙽 𝚃𝙷𝙴 𝙿𝙸𝙲𝚃𝚄𝚁𝙴𝚂 , 𝙼𝚈 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺 𝚅𝙴𝚁𝚈 𝙶𝙾𝙾𝙳 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳. 𝚂𝙾 𝙱𝙴𝙵𝙾𝚁𝙴 𝚈𝙾𝚄 𝙶𝙸𝚅𝙴 𝙱𝙰𝙳 𝚁𝙰𝚃𝙸𝙽𝙶 𝚃𝙾 𝙼𝚈 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂, 𝙱𝙴 𝚂𝚄𝚁𝙴 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽 𝙰𝙽𝙳 𝙰𝚂𝙺 𝚃𝙾 𝚈𝙾𝚄𝚁𝚂𝙴𝙻𝙵 , 𝚆𝙷𝚈 𝚈𝙾𝚄 𝙳𝙾𝙽'𝚃 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽. 𝙸 𝙳𝙾𝙽'𝚃 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚄𝙿𝙻𝙾𝙰𝙳 𝙰 𝙻𝙾𝚃 𝙾𝙵 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂 𝙵𝙾𝚁 𝙴𝙰𝙲𝙷 𝚂𝙸𝙽𝙶𝙻𝙴 𝙿𝚁𝙾𝙱𝙻𝙴𝙼 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰𝙽𝙳 𝙵𝙾𝚁 𝙴𝚅𝙴𝚁𝚈 𝚂𝙸𝙽𝙶𝙻𝙴 𝙼𝙾𝙳𝙴𝙻! 𝙴𝚅𝙴𝙽 𝚈𝙾𝚄 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚂𝙷𝙰𝚁𝙴 𝙾𝙽𝙴 , 𝙸𝚃 𝙳𝙾𝙴𝚂𝙽'𝚃 𝙼𝙰𝙺𝙴 𝚂𝙴𝙽𝚂𝙴 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚂𝙸𝙼𝙿𝙻𝙴 𝙼𝙾𝙳𝙴𝙻 𝙸𝚃𝚂𝙴𝙻𝙵!

𝙿𝙻𝙴𝙰𝚂𝙴, 𝙻𝙸𝙺𝙴 𝙸 𝚂𝙰𝙸𝙳 𝚃𝙷𝙴 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺𝚂 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳 𝙴𝙰𝚂𝚈! 𝙽𝙾𝚃 𝙰𝙻𝚆𝙰𝚈𝚂 𝚁𝙴𝙳𝚄𝙲𝙸𝙽𝙶 𝚃𝙷𝙴 𝚂𝙿𝙴𝙴𝙳 𝙲𝙰𝙽 𝙷𝙴𝙻𝙿 𝚈𝙾𝚄 𝚃𝙾 𝚂𝚃𝙸𝙲𝙺 𝙴𝚅𝙴𝚁𝚈 𝙼𝙾𝙳𝙴𝙻 𝙾𝙽 𝚃𝙷𝙴 𝙿𝙻𝙰𝚃𝙴! 𝚃𝙷𝙰𝙽𝙺 𝚈𝙾𝚄 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚄𝙽𝙳𝙴𝚁𝚂𝚃𝙰𝙽𝙳𝙸𝙽𝙶!

ᴵᶠ ʸᵒᵘ ʰᵃᵛᵉ ᵖʳᵒᵇˡᵉᵐˢ ᵃᵇᵒᵘᵗ ᵗʰᶦˢ ᵐᵒᵈᵉˡ, ʲᵘˢᵗ ˢᵉⁿᵈ ᵐᵉ ᵃ ᵖʳᶦᵛᵃᵗᵉ ᵐᵉˢˢᵃᵍᵉ ᵃⁿᵈ ᴵ'ˡˡ ʰᵉˡᵖ ʸᵒᵘ.

ᴳᶦᵛᵉ ᵐᵉ ᵃ ˡᶦᵏᵉ ᵃⁿᵈ ᶠᵒˡˡᵒʷ ᵐʸ ᵖᵃᵍᵉ.

ᵀʰᵃⁿᵏ ʸᵒᵘ ᵗᵒ ˢᵘᵖᵖᵒʳᵗ ᵐᵉ ᵃⁿᵈ ʰᵃᵖᵖʸ ᵖʳᶦⁿᵗᶦⁿᵍ.

Comment & Rating (374)

@Omthetortoise

Print Profiles are not remixes. Your model does not get altered in any way by adding a print profile. Trying to prevent people from helping to get your model out there seems self-defeating. It's also in contrast to the way MakerWorld is designed. If someone figures out the settings for this to print on a 10 year old I3, why would you want to prevent them from helping get your model in front of others running the same machines?

@robere2

Yes I agree it's a silly hill to die on, but copying from another comment, the license says "You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object" When you upload a print profile, it asks for a .3MF file. Is it possible to upload a .3MF file that does not contain the model? Does MakerWorld strip the model from your .3MF file and replace it with the original? Is there a special case in the license used that allows specifically unmodified models in print profiles?

@rovex32

Replying to @robere2 :

'Modifying' in BL slicer doesn't change the model, it changes settings that apply to the original model, therefore they aren't a remix. A Remix is a modification to the geometry data itself, this isnt what BL slicer does.

@robere2

Replying to @rovex32 :

Of course. The license gives remixes as an example. It does not allow re-uploads at all, regardless of whether they are a remix or not, hence my question (I'm not sure where this discussion about remixes even came from...)

(Edited)

@Admin

Origibal creator doesn’t understand licensing choices and is quite rude not worth the effort of printing anything from this guy.

@blazentrance

Print Profile

STANDARD WITHOUT LOGO

Support and hole design may need tweak

(Edited)

Other Issues:Support makes hole rough that could be obstacle to put silicone plane into.

The designer has replied

@EngineeringProj

it doesn't need anything. if you don't like it , build your own one!

@user_3393025028

Replying to @EngineeringProj :

But you don't allow remixes :(

(Edited)

@Infantryman

Replying to @EngineeringProj :

Put your ego away geez! Go get some fresh air outside! If I would building my own, it WOULD work fine. But I would still take criticism as positive!

(Edited)

@WinstonSmith

Print Profile

STANDARD

Other Issues:hits toolhead

The designer has replied

@EngineeringProj

It hits anything! Stop talking bad.

@EngineeringProj

YOU LIE!

GIF

@Sideduck

Replying to @EngineeringProj :

Joe Wilson, is that you?

(Edited)

@p.ostlender

Print Profile

STANDARD WITHOUT LOGO

(Edited)

Other Issues:didn't really work. Have to make some adjustments so that it fulfills the purpose. Would like to provide my model with the adjustments but I was forbidden by the creator...

The designer has replied

@EngineeringProj

Thank you!

@RayHbigdog

I had a problem with it also .it printed well but it fit so loose it would pop up and cause problems with my print. I tossed it because I didn't trust it.

(Edited)

@allprintingpine

Print profiles aren’t remixes… read up on this topic

@Rick269

Not sure if there is an error but the stock profile has ABS filament but with the cool plate?

The designer has replied

@EngineeringProj

Reported for misinformation.

@Rick269

Replying to @EngineeringProj :

where is the misinformation? I have even posted a screenshot.

@Stephanos

In case this doesn't work for you, here are some alternatives (that you can also remix): https://makerworld.com/en/models/186746#profileId-205631 https://makerworld.com/en/models/178152#profileId-196031 https://makerworld.com/en/models/179704#profileId-212971

@SimplePrinter

Thanks! those are great

@ac.grolimund

Print Profile

STANDARD WITHOUT LOGO

Gedruckt in PETg sehr gute passform sehr gute setings Fahr/Haltewege des X1C passen nicht zu dem Design. Drucker startet auf dem Silikon und presst Filament heraus, wodurch der ganze Kopf verklebt wird. Das selbe beim Pausieren und nach dem 1 Layer check.

(Edited)

GIF

The designer has replied

@EngineeringProj

Servus, danke!

@ac.grolimund

Replying to @EngineeringProj :

Leider musste ich gerade feststellen, dass es nicht geeignet ist für den X1C, dieser parkt genau auf dem Silikon. Sprich man muss den Code ändern, falls das überhaupt geht, sodass die Pause Position und Rückfahrposition mehr auf der linken Seite ist. PS, dies habe ich allerdings nur, wen ich während eines Drucks auf Pause drücke. Ich muss es noch testen wie es sich verhält, wen man normal einen Print startet und der normal durchläuft. 1% grösser Skalieren ist auch bei mir nötig, da es bei einer 100% Skalierung beim Reinigen herausgezogen wird.

(Edited)

@EngineeringProj

Replying to @ac.grolimund :

Ich hab kein Problem seit Juni.

@kstudioca

I think I should add a new print profile, this model doesn't have a profile to print on my A1 Mini. As you see in the screenshot, I am unable to print from it. I'm going to load it on my computer and make one for A1 mini users + AMS color logo. Or someone can do it for me. :)

@mrmike

Replying to @EngineeringProj :

again. such a nice helpful content creator that thinks he is god. someone asked for help and you wanna be a douche canoe.

@LayersByMarc

Replying to @mrmike :

I have never seen more of a whackjob in a situation like this. The creator is off the wall.

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.