Prints (0)

Description

This model was specifically developed for the Pinshape Mechanical Design Competition. To see an explanation of what it does, how to put it together, and how to win the game, see the video below:

Design Notes

Page 1 of my notes are simply the design requirements. Certain elements that I wanted to drive the design. This includes minimal support material when printing, minimal bluing and non-3d printed parts when assembling, and so on and so forth.

The first sketches I made were centered around the input mechanism and the "winning" indicator. And the first problem presented itself. How were we going to turn speed into winning? As the user pushed faster and faster on the levers, somehow that increase in speed needed to indicate something both visually and audibly. That's when flyball governors came to mind. Except this governor wasn't going to open or close a valve like on old steam engines. THIS governor was going to make noise.

Page 3 is me refining the ideas of the input mechanism to include springs, as well as the first scale sketches of the governor mechanism.

I learned two things with my first governor experiment. One, moderate rotational force was adequate for raising and lowering the arms. Two, my governor needed to be much smaller in order to keep the "noise cage" printable. MUCH smaller. Page 4 shows ways to reduce the overall size and a to-scale sketch of the desired noise cage.

Keeping the input mechanism support, glue, and fastener free was a definite challenge. Page 5 shows lots of different ideas and the evolution of certain ideas.

On page 6 I finally get to the print-in-place hinge design. This includes the first real design ideas for the rack (of the rack and pinion design) that will translate a user's input into rotational motion.

After figuring out that I needed to step up the RPM going to the governor, I sketched a simle gearbox that would be easy to print without supports and that I could work into my design easily. That work is on page 7.

Print Settings

These models were printed on the Original Prusa i3 MK2 out of Hatchbox Green PLA filament. Due to variations in printers and filaments, certain aspects of this design (sliding contact joints, gear meshes, snap fits, etc.) may not perform as they did for me. In an effort to reduce that risk, you will find all my slicer settings below.

 

Settings that were common between all prints:

 

Layer Height:  0.2 [mm]

Extrusion Multiplier:  1.00

Extrusion Width:  0.48 [mm]

 

Retraction Distance:  0.8 [mm]

Retraction Speed:  30.0 [mm]

Coast at End:  0.20 [mm]

 

First Layer Height:  100%

First Layer Width:  95%

First Layer Speed:  60%

 

Temperature_First Layer: 195 [deg C]

Temperature_All Other Layers: 190 [deg C]

Temperature_Heated Bed:  55 [deg C]

 

Cooling_First Layer:  0 [fan speed]

Cooling_All Other Layers:  100 [fan speed]

 

Filament diameter: 1.73 [mm]

Settings for 90 Deg Gear_Governor, 90 Deg Gear_Output, Coupled Gear, Frame Clip, Frame Hood, Governor_Arm1&2, Governor_Clip, Governor_Flapper, Noise Cage, Rack_Hinged, and Spring Gear :

Supports Disabled

Wipe Nozzle Distance:  2.00 [mm]

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  3

 

Infill: 20%

 

Printing Speed: 40 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  80 [mm/s]

 

Settings for the all Shafts:

No Supports

Wipe Nozzle Disabled

 

Top Solid Layers:  6

Bottom Solid Layers:  6

Perimeter Shells:  3

 

Infill Percentage: 20%

 

Adjust Printing Speed for Layers Below {time} Disabled

Printing Speed: 25 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  40 [mm/s]

 

Settings for the Frame and Hood:

Supports Disabled

Wipe Nozzle Distance:  2.00 [mm]

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  2

 

Infill: 20%

 

Printing Speed: 40 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  80 [mm/s]

 

Settings for the Rack Pins, Limit Pin, and Governor_Pin:

Supports Disabled

Wipe Nozzle Disabled

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  3

 

Infill: 20%

 

Adjust Printing Speed for Layers Below {time} Disabled

Printing Speed: 25 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  40 [mm/s]

 

Settings for the Pinions:

Supports Enabled

Support Infill Percentage:  30%

Extra Inflation Distance: 1.40 [mm]

 

Wipe Nozzle Distance:  2.00 [mm]

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  3

 

Infill: 20%

 

Printing Speed: 40 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  80 [mm/s]

 

 

Settings for the Rhythm Hub:

Supports Disabled

Wipe Nozzle Distance:  2.00 [mm]

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  3

 

Infill: 15%

 

Printing Speed: 40 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  80 [mm/s]

 

Settings for the Springs:

No supports

 

Wipe Nozzle Distance:  2.00 [mm]

 

Top Solid Layers:  3

Bottom Solid Layers:  3

Perimeter Shells:  3

 

Infill: 100%

 

Printing Speed: 40 [mm/s]

Outline Underspeed:  80%

X/Y Axis Movement Speed:  80 [mm/s]

Design Files

File Size

Frame Hood.stl
45.8 KB
Governor_Main Shaft.stl
65.5 KB
Frame.stl
539 KB
90 Deg Gear_Governor.stl
558 KB
Governor_Arm1.stl
48 KB
Governor_Arm2.stl
48.7 KB
90 Deg Gear_Output.stl
679 KB
Governor_Pin.stl
38.6 KB
Governor_Clip.stl
101 KB
Governor_Flapper(need2).stl
5.36 KB
Coupled Gear Shaft.stl
41 KB
Coupled Gear.stl
806 KB
Input Shaft.stl
48.3 KB
Frame Clip.stl
17.1 KB
Rhythm Hub Shaft.stl
70.1 KB
Rhythm Hub.stl
106 KB
Spring Gear.stl
744 KB
Spring(need5).stl
269 KB
Limit Pin.stl
60.7 KB
Noise Cage.stl
4.69 MB
Pinion_Middle.stl
315 KB
Pinion_Pinkie.stl
291 KB
Pinion_Pointer.stl
322 KB
Pinion_Ring.stl
297 KB
Rack Pin(need 4).stl
41.1 KB
Rack_Hinged(need4).stl
518 KB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×