ATTENTION! READ CAREFULLY BEFORE PURCHASING: The print has only been tested on resin, due to its details, good results are not guaranteed on filament printers.
-Downloading only entitles the purchaser to personal use of the file. -
-It is forbidden by the author the commercialization, transfer or profit of the file by unauthorized third parties.
-Modification of the original file is prohibited.
-This is a model for diorama decoration, the wheels.
do not rotate.
PRINTER: Anycubic Phpton Mono x 6k
3D PRINTING PARAMETERS
-Printed using LycheeSlicer software.
-It is designed to be printed in resin. The results in
PLA may not be satisfactory.
-It is possible to print it with automatic media, however it is.
important to deactivate the auto orientation tab in the
The supports would spoil the details of the
sides.
-At scales between 1:400 and 1:500 light brackets give the best results.
-The ideal is to print the part as is (as if the wheels touch the printing plate) but adding the supports, obviously.
-I added a file with the parameters and the ideal printing position for reference.
BASE LAYERS:
-Number of layers: 6
-Exposure time: 28s
-Transition layers counter: 3
-Lift distance: 4 - 3 mm
-Lift speed: 60 - 180 mm/m
-Retract Speed 60 - 180 mm/m
NORMAL LAYERS
-Layer height: 34 um
-Light off delay 1s
-Exposure time 3.5 s
-Lift distance: 3 - 4 mm
-Lift Speed 60-180 mm/m
-Retract Speed 60- 180 mm/m
SCENE SCALE COMPENSATION
-Scale X: 100% -Scale X: 100% -Scale X: 100% -Scale X: 100% -Scale X: 100%
-Scale Y: 100% -Scale Y: 100%
-Scale Z: 100%
-A white primer coat is recommended before painting vehicles.
ATTENTION! READ CAREFULLY BEFORE BUYING: The print has only been tested in resin, due to its details good results are not guaranteed in filament printers.
-The download only gives the right to a personal use of the file by the person who buys it. -
-It is prohibited by the author the commercialization, assignment or benefit of the file by unauthorized third parties.
-Modification of the original file is prohibited.
-This is a model for diorama decoration, the wheels
they don't rotate
PRINTER: Anycubic Photon Mono x 6k
3D PRINTING PARAMETERS
-It has been printed by LycheeSlicer software.
-It is designed to be printed in resin. The results in
PLA cannot be satisfactory.
-It is possible to print it with automatic supports, however it is
important to disable the auto orientation tab of the
piece, since the supports would affect the details of the
sides.
-In scales between 1:400 and 1:500, light supports are the ones that give the best results.
-The ideal is to print the piece as it is (as if the wheels touched the printing plate) but adding the supports, obviously.
-I add a file with the parameters and the ideal printing position as a reference.
LAYER BASE:
-Number of layers: 6
-Exposure time: 28s
-Transition layer counter: 3
-Lifting distance: 4 - 3 mm
-Lifting speed: 60 - 180 mm/m
-Retraction speed 60 - 180 mm/m
NORMAL LAYERS
-Layer height: 34um
-Light off delay 1s
-Exposure time 3.5s
-Lifting distance: 3 - 4 mm
-Elevation speed 60-180 mm/m
-Retraction speed 60- 180 mm/m
SCENE SCALE COMPENSATION
X-Scale: 100% -X-Scale: 100% -X-Scale: 100% -X-Scale: 100% -X-Scale: 100%
-Y-Scale: 100%
-Z-Scale: 100%
-A coat of white primer is recommended before painting vehicles.