Skip to content

Anycubic I3 with SKR1.3 32bit + Marlin 2.0

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 4.5/5 (1 vote)
Evaluation of members on the printability, utility, level of detail, etc.
  • 1.8k views
  • 17 downloads
License
3D design format
Folder details Close
  • BIGTREETECH_SKR_V1_3_Anleitung_deutsch.pdf
  • BLT_V6_Vulcano.stl
  • Kontermutter.stl
  • SDHalterung.stl
  • SD_Deckel.stl
  • SKRAdapter.stl
  • SKRklebAdapter.stl
  • STARTCODE.txt
  • mks_config.txt

Learn more about the formats
Publication date 2022-09-17 at 10:54
?
Published to Thingiverse on: 2019-05-22 at 02:00
Design number 849439
Michelix

Michelix

3D printer file info

3D model description

#English#

Adapter for Bigtreetech SKR 1.3 to Anycubic I3 Mega

Firmware is for TMC2208 2.0 or higher with UART (without filament sensor (activatable))
with BLTouch

You need:
Motherboard SKR 1.3
5 TMC2208 V2
Display eg: KSR TFT35 and/or 12864 RepRapDiscount Full Graphic Smart Controller
USB-B extension
SD card extension
Plugs and sockets
Antlabs BL Touch V3
M3 bolts and nuts
3-wire strand
Capazitator 500 µF at 5V (when u use 2 Display at the same time.)

Disadvantage:
The case fan is not controllable.
To place the display in the housing, a screw guide in the Any must be broken away and a corner filed off the display.
It gets louder again.

Advantages:
The firmware and the display are modifiable
The TMC2208 can easily be operated in UART mode.
32bit, steps are calculated faster.
Further tests are still pending.

Who wants to edit Marlin2.0 itself> Instructions in the Word file

KSR TFT35 firmware in German
https://www.dropbox.com/sh/p2sasy5zqlv8p8d/AACfHpKsdgP0HpKn0R2wpLNpa?dl=0&fbclid=IwAR0P50o_vpGmIDOrSjcSxwBKwXdFp0VWY8x1WebyNDrfhNkckPojH20wq0c

!!! change baud rate to 115200 baud in config.txt !!!

The board also supports 2.8-inch and 3.5-inch color touchscreens and 2004 LCD and 12864 LCD.

It soon follows:
Modified display firmware.

The installation of the faster motherboard is worthwhile only if the Any has been mechanically improved.
https://www.thingiverse.com/thing:3589645

Problems:
checksumme error while printing from SD-Card at TFT32

#Deutsch#

Adapter für Bigtreetech SKR 1.3 zu Anycubic I3 Mega

Firmware is for TMC2208 2.0 or higher with UART (ohne Filamentsensor (aktivierbar))
mit BLTouch

Benötigt wird:
Motherboard SKR 1.3
5 TMC2208 V2
Display z.B.: KSR TFT35 und /oder 12864 RepRapDiscount Full Graphic Smart Controller
USB-B Verlängerung
SD-Kartenverlängerung
Stecker und Buchsen
Antlabs BLTouch V3
M3 Schrauben und Muttern
3adrige Litze
Kondensator ca. 500µF ( an 5V zum Betrieb von 2 Diplays gleichzeitig)

Nachteile:
Der Gehäuselüfter ist nicht steuerbar.
Um das Display im Gehäus zu plazieren muss eine Schraubenführung im Any weggebrochen werden und eine Ecke vom Display abgefeilt werden.

Vorteile:
Die Firmware und das Display ist modifiezierbar
Der TMC2208 ist problemlos im UART-Modus betreibbar.
Bei verwendung eines LCD 12846 kann man auch während des Druckes an viele Variablen verstellen.
32bit, Schritte werden schneller berechnet.
Weitere Tests stehen noch aus.

Wer Marlin2.0 selber bearbeiten möchte > Anleitung in der Word-Datei

KSR TFT35 Firmware in Deutsch
https://www.dropbox.com/sh/p2sasy5zqlv8p8d/AACfHpKsdgP0HpKn0R2wpLNpa?dl=0&fbclid=IwAR0P50o_vpGmIDOrSjcSxwBKwXdFp0VWY8x1WebyNDrfhNkckPojH20wq0c

!!! change Baudrate to 115200 Baud in config.txt !!!

Das Board unterstützt auch von 2,8-Zoll- und 3,5-Zoll-Farb-Touchscreens und 2004 LCD und 12864 LCD.

Es folgt bald:
Modifiezierte Display firmware.

Der Einbau des schnelleren Motherboard lohnt sich nur wenn der Any schon mechanisch verbessert wurde.
https://www.thingiverse.com/thing:3589645

Gehäuse für 12846
https://www.thingiverse.com/thing:2813298

Probleme:
Beim Drucken von SD-Karte des TFT32 Checksummenfehler

3D printing settings

-

Tags

Advertising

Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi 💜.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.