(big V23 and N23 update!)
the 50 and 68 cal N23 mount have been added. the original mount is renamed to v23
this matters if you want to chance over to the new N23 mag slide part
also the front mounts have been changed so it haves a better fit with the magazine.
and the wide 50 and 68 cal mag mound have been added as well called NW64. those only work with the N23 mag slides
about the front mounts. I find that the 0mm backwards front mounts work the best.
but in case you have a slightly smaller mag by compressing the first view layers of your mag then you might like the 0.5mm backwards front more. all do I have to say the 0mm should work for that one as well.
(the mount is for the 68 cal and 50 cal mags)
I wanted to call this a universal mag mount but of course there are a lot of milsim type of markers that will not fit this mount not with some modding…
but markers that have a form factor of a subair marker like autocockers, pump versions of auto cockers, spyders, should work with this mount.
there are a view different barrel to feed neck hight’s out there and barrel sizes.
if the hight of the mount don’t work out for you then just let me know. and i will add that hight. the hight is measured by measuring the center of the barrel up to the top of the feedneck. the picture shows what I mean by this.
Front mounts variations:
as you can see on the pictures are there a view options when it comes down to the front morning part. this is so you can have custom look. but at the same time also to make this mag mount more flexible for the current mags and future designs.
but the original P90 design does help in guiding the mags into place. so in case you don’t like the tall look to the original the low wigged is a good middle ground
MAG activation screw:
I do say that the grub screw needs to be at 2mm in hight. that functions to activate the magazines. but it’s possible that is need a slight adjustment. this will be covered in the UNW P90 PDF. I do like the idea of having a smooth top on the grub screw so that is why I like it to be installed the what it’s shown with the hex key mount hole at the bottom of your Mag mount.
The Slide:
the slide. you want the slide to move smoothly and not get stuck when it’s fully compressed. this can be because of support remains or elephant food. but you can also play around with the spring tension if you like I used to use 2 springs with a 0.5mm wide instead of the now recommended 0.6mm wire. since I noticed that adding 1 extra spring with some stiff wire was actually a lot better. so you may want to play around with it so the slide is sliding al the way forward every time when the mag is placed in the mount.
Shroud note:
it got a M-lok mounting option at the bottom. but do keep make sure that the bolts of your M-lok accessory is not to long other wise you might damage you barrel!
compatibility note:
for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like to switch to one or the other.
feedneck to barrel center hight
40mm: PROTO
43mm: PE EGO, PE ETEK,
45mm: PE GEO, PE ETHA’s, PE EMEK
also there are a view barrel options
shaft 2
shaft 4
emek 3
barrels with a OD from: 21.40mm, 22.00mm, 22.50mm, 23.00mm, 23.50mm, 24.00mm, 24.50mm
Video Links:
Video Links to mag options for this mount:
UNW P90 Project update: ESG Euro SuperGame 2022 after report
https://odysee.com/@UntangleWORKS:a/UNW-P90-2022-update-ESG-after-report:2
UNW P90: step by step mag function check (and a bit of a update)
https://www.youtube.com/watch?v=BqOoVJ2hh8s
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-function-check:b
UNW P90 MAG VS those... other paintball MAGS
https://www.youtube.com/watch?v=S-up50s3zvo
https://odysee.com/@UntangleWORKS:a/UNW-P90-MAG-VS-those-other-MAGS:2
UNW P90 mag assembly video
https://www.youtube.com/watch?v=eI5-sqQGx0I
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-assembly:b
UNW P90 mag assembly for the open mag version
https://odysee.com/@UntangleWORKS:a/UNW-P90-windows-mag:f
The UNW P90 Hi cap mag or in other words a hopper adapter for the UNW P90
https://www.youtube.com/watch?v=A3yAlBoDHIg
https://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap:b
UNW P90 Hi cap mag lid
https://www.youtube.com/watch?v=L9vtBMNIMkM
https://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap-lid:4
demo about the mag plugs at 12:20
https://youtu.be/0uPL_J2TmEE
UNW P90: Template ring for the P90 airsoft mags
https://youtu.be/kufvl5E0RiU
UNW P90: G11 styled tippmann Tipx mag adapter
https://www.youtube.com/watch?v=_U-nBrJH1hM
https://odysee.com/@UntangleWORKS:a/UNW-P90-G11:a
UNW P90 mag winder
https://youtu.be/v1cIc2swRdg
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder:9
UNW P90 mag winder ring
https://youtu.be/KMoFYRpW4_E
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder-ring-B:9
UNW P90 mag speed loader
https://youtu.be/lVzFHDjsehg
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader:a
UNW P90 mag speed loader bumper
https://youtu.be/4S5K_jraJXI
https://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader-bumper:6
materials needed:
MAG mount:
2x spring 6mm OD, 0.6mm wire, 20mm long
Note: you can add one more if you like it to give the slide more power
2x M2.5 Bolt 16mm long
1x M5 grub screw
Note: this needs to stick 2mm up from the mount, use some calipers for this.
1x M5 bolt 25mm long
3x M5 bolt 35mm long
RING style mount:
4x M3 bolt 16mm long
Shroud style mount:
8x M3 bolt 16mm long
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/413d34bc-3905-4f10-8d99-e2ba4d9884f4/UNW-P90-MOD-RING.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/9e21c21d-c37f-4b43-9d3e-81db60097193/UNW-P90-MAg-pouch.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/5c8297d1-ab69-4257-9426-b655922e1bcf/UnW-p90-cleaning-snake.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/f295bdff-6b9d-47c1-ba35-db118b7cdb42/UnWsprayframe.jpg)
