Foo Fighters FanArt Double Sided Hanging Art w/ Stain Glass Effect

The grunge / alternative rock and roll band Foo Fighters became an instant success upon the release of their self-named debut album, Foo Fighters, on July 4, 1995. Nearly 30 years later, their fan base continues to grow in strength and numbers. In celebration of the countless Gen-Xers who've faithfully followed the band and mourned the loss of drummer Taylor Hawkins in 2022, we present to you this unique Foo Fighter Stained Glass Hanging Fan Art.

It's designed in the same style as our Stained Glass Series (see below) of luminescent indoor/outdoor window and garden decor. It has sturdy front and back panels, with ultra-thin (0.32mm) color panels inside. The colors print so thin they become translucent, mimicking the effect of double-sided stained glass art.

ASSEMBLY INSTRUCTIONS
There are a total of 4 STL files in the ZIP file. Note the "WHOLE" file is just for display on Cults3D, and is not meant for printing. See images above for instructional pictures to help with assembly. The file names include the colors I used (all in iiiDMAX PLA+ filament). Feel free to change them up as you wish.

• Foo Fighter FanArt - Bottom (White)
• Foo Fighter FanArt - Top (White)
• Foo Fighter FanArt - FF (Black)
• Foo Fighter FanArt - Glass (Red)

Each color piece has been carefully rendered to fit perfectly into the recessed areas of the "Bottom" section. They are ultra-thin and should only print 2-layers thick (at 0.16 Layer Height). This is important to ensure a translucent print, and that light is able to illuminate softly through the other side.

Inserting the colors is like doing a child's puzzle. It is very easy to tell what goes where. Use tiny dots of glue to secure each of these in place.

Next, add glue to the underside of the Top section. Only use tiny dots, but a lot of them for good adhesion. Then line up the Top section over the Bottom and gently press them together. Use clips or clothes pins to hold the pieces together and allow ample time to dry. I like to use fishing line and/or a small keyring to hang them.

Enjoy!

DIMENSIONS
Fully assembled, the stained glass Foo Fighters Band Hanging Decoration measures:

X = 19.0cm / 7.5in
Y = 19.7cm / 7.8in
Z = 0.35cm / 0.14in

If you like the Foo Fighters Fan Art, be sure to check out other pieces in the Stained Glass Series:

• Dragonfly
• Butterfly
• Hummingbird
• Cardinal
• Tulip Heart
• Wings of Love Angel Heart
• Tribal Dream Catcher
• Sunflower
• Winking Wendy Frog
• Lady of the Garden Wreath
• DMB Flame Dancer

IMPORTANT: Unless otherwise noted, ALL GetPrinted3D designs are Copyright protected. When you purchase a file, you do NOT have the right to sell the file or printed model. Files may not be redistributed under any circumstances. The models are for personal and private use, and may not be sold commercially without the explicit written consent of GetPrinted3D.

You can obtain a Commercial License to legally sell our designs here:
- https://www.patreon.com/GetPrinted3D

TOP & BOTTOM
These sections will print well under basic settings.

Layer Quality: 0.2
Infill: 20%
Speed: 60mm/s
Supports: No
Plate Adhesion: None

MIDDLE PIECES (Black FF & Red Glass)
These pieces must print very thin to remain slightly translucent. They are only 0.32mm thick. Use the following settings to ensure they print in just two layers.

Layer Quality: 0.16
Initial Layer: 0.16
Infill: 100%
Speed: 40mm/s
Supports: No
Plate Adhesion: None

Tip: If you're having trouble printing these smoothly, try using Cura's 'Enable Ironing' setting. It takes a little longer to print, but the nozzle will go back over the top layer to smooth it out, just like you would iron clothing to remove wrinkles.