mouseFPV Quad Accessories

Overview

These are the parts I use on my quads. Everything is in the proper printing orientation for minimal supports, strength, and printing speed. DO NOT print the mounts 'bottom down' for the layer lines will become a weakpoint in your base and you can lose the gopro. Highly recommend washers on all mounts, RDQ has nice countersunk ones. I try not to add extra things I dont need to my quads, and try to keep them as light as possible.

PRINT 3 WALLS ON EVERYTHING. These were designed to use 3+ walls and minimal infill to save weight.

Notes in order:

• cap_holder_external_1000.stl
  • cap holder to go around a standoff and put a 1000uf panasonic fm 35v cap "on the deck" for 10mm caps
• 13mm sonicare_cap_holder_external_1000_fr
  • cap holder to go around a standoff and put a 1000uf panasonic fr 35v cap "on the deck" for 13mm caps
  • No supports
• session band new sonicare.stl
  • Band to keep your session from blowing out the side.
• sonicare_session_30.stl
  • 30 degree Hero Session Mount. Camera Butter ND filter friendly (slides in with one on). sides are open. Optionally, you can print the session band to slide over it. I also find as time goes on and the mount losens up, you can add some electrical tape to the bottom of the session to tighten it back up. This is made to be very light and very durable. Fits all standard (short base) Fpvcycle quads No, I wont make you a 20 Degree mount, use tinkercad...
  • Only needs supports for the button cutout, and front opening.
  • 3 walls
  • 16% infill (i use gyroid)
• Sonicare hero 9.stl
  • 30 degree Hero 9 or 10 Mount. Camera Butter ND filter friendly (slides in with one on). you need to cut a slit where there is a seam along the top over the lens area. small bump above lens is made to provide some protection. You need to push the area around the lens ALL THE WAY ON or it will be in view. there are slits so you can see important info on the front screen. This is made to be very light and but durability isnt anything to write home about. It has what it needs in all the right places but I was between I giant mount and one of those half mounts and wanted full coverage around the gopro. Had a bit of extra height to clear bent props. No, I wont make you a 20 Degree mount, use tinkercad...this covers the battery area and has extra protection over the USB port so you can run no battery and use a BEC
  • needs supports (lots of waste here)
  • 3 walls
  • 16% infill (i use gyroid)
• sonicare_toesies_2.stl
  • These are friction fit arm gaurds. very tight fit, harder to get on than Keira Knightley's corset in the first Pirates movie. They are as light as possible, and are considered disposable/sacrificial layer. I usually put new ones on every 3-5 fly days. Arms can break and thats fine, but I HATE getting carbon splinters. HATE IT. Thick side down....
  • If your printer is well tuned you shouldnt need supports. If you use them, they are a pain to get out. Small imperfections in the inside dont matter much.
  • 3 walls
  • 16% infill, you should end up with a little infill at the tips when slicing.
• Ghost Atto FPVCycle Prototype
  • This is just a crappy version/ripoff of Ridwan Hughes idea. Its a folding antenna mount for ghost antenna. He originally came out with the idea for the tiny trainer minimortal-T for this. so I made one for ghost. I think he has since made ghost versions, so if you want something nicer, look to his designs. here (https://www.thingiverse.com/thing:4662724). This should also fit the cinesplore and the fouride if I am not mistaken
  • Print settings dont really matter. Make sure your first layer is good.
• Vista_Antenna_Mount.stl
  • Rear Vista antenna mount for the fouride. shorter in height than the one for the prototype this may work on the cinesplore as well.
  • no supports
  • 16% infill
• Vista_Lolipop_Cover.stl
  • This is made to protect your vista antenna from becoming a baby rattle. slide it over from the bottom. You have to unplug the antenna to get this on/off
  • No supports
  • infill does not matter
• sonicare hero 9.stl *