Hi, Translation at the end in EN.
Hi Ihr, Ich möchte euch hier einmal eine kleine Multimedia Box für den Betrieb eine Hausautomation Präsentieren:
Aufbau 3 Kammern, die Trennwände können raus getrennt werden, müssen jedoch falls nicht geklebt werden. Die Linke Kammer ist für den Bass / Breitband Lautsprecher gedacht, da in der Heckbereich eine aussparung für eine Membrane und im Deckel ein Sternloch vorhanden ist. Die Ecken sind für Hochtöner gedacht. Im vorderen Bereich Sind 2 Vertikale Stege für einen LED Strip vorhanden und ein Horizontaler Steg für die Respeaker Leds. Eine Halterung für einen 2 Hat Respeaker liegt bei, hier müssen lediglich 2 Kleine Löcher für die Mics und ein Loch für den Knopfstift gebohrt werden.
Dekoriert mit kleinen Kacheln
Der Grund liegt auf der Hand. "Alles in einem Kasten"
Raspberry, Microfon, Lautsprecher, Verstärker, SSD, Sticks ect.
Eine Kamera kann zusätzlich im unteren bereich des Horizontalen Steges eingebohrt werden. Der Platz wäre vorhanden.
Hinweis beim Zusammenbau :
Bei der Benutzung von Heißkleber bitte schnell arbeiten, da die Wände bei zu geringer Füllung schmelzen.
Die Halterungen der Lautsprecher bitte erst an diese Montieren und dann an die jeweiligen Stellen kleben.
Die Trennwände können getrennt werden, unten mit scharfen Messer einritzen und Brechen.
Beim Kleben bitte eine Flache Oberfläche nehmen, da sich sonst die Teile Verziehen können.
Info: Zur Verbindung vom Raspberry mit dem Pi Hat ist ein Verbindungskabel notwendig
Maße 38cm x 18cm x 9cm
Ohne Zubehör, nur die Dateien.
Nur für den Eigengebrauch, Keine Vervielfältigung oder Verkauf
Änderungen sind evtl bei Anfrage möglich.
License : CC BY-NC-ND
Benutztes Material am Ende.
Hi you, I would like to present you here once a small multimedia box for the operation of a home automation:
Structure 3 chambers, the partitions can be separated out, but if not glued. The left chamber is designed for the bass / broadband speaker, as there is a recess for a diaphragm in the rear area and a star hole in the lid. The corners are intended for tweeters. In the front area there are 2 vertical bars for an LED strip and a horizontal bar for the Respeaker Leds. A holder for a 2 hat respeaker is enclosed, here only two small holes for the mics and a hole for the button pin must be drilled.
Decorated with small tiles
The reason is obvious. "Everything in a box"
Raspberry, microphone, speakers, amplifiers, SSD, sticks ect.
A camera can also be drilled in the lower area of the horizontal bar. The place would be available.
Note when assembling:
When using hot glue, please work fast as the walls will melt if the filling is too low.
Please attach the brackets of the loudspeakers first to these mountings and then to the respective places.
The partitions can be separated, carving down with sharp knives and breaking.
When gluing, please take a flat surface, otherwise the parts may warp.
Dimensions 38cm x 18cm x 9cm
For personal use only, no duplication or sale
Changes may be possible on request.
License: CC BY-NC-ND
Only Case , Not Speakers ect.
ReSpeaker 2-Mics Pi HAT für Raspberry
Loch des BB / BB Lautsprechers im Deckel 80 mm ( 8cm )
2x Mylar-Hochtöner 6cm
4 Füße für Lautsprecher, Gummi Boxen Füsse, 10mm
78*41mm Lautsprecher Bass Membrane