LARGE Ghost Fully Detailed Model, LED Illuminated, no supports!

Released by popular demand!!!

New Larger version, about 40% larger! Closer to the appropriate scale in the game.

Make your own fully detailed model of Ghost companion!

Fully printable without supports. More details on printing under the Instructions Tab.

I like having it assembled with magnets, but I understand some people may want it 100% printable. If there is enough interest I will alter the model to fully snap together without magnets.

Link to LED Light: http://www.ebay.com/itm/171239692713?_trksid=p2059210.m2749.l2649&var=470455566681&ssPageName=STRK%3AMEBIDX%3AIT

Link to Magnets:

http://www.homedepot.com/p/Magcraft-Rare-Earth-1-4-in-x-1-16-in-Disc-Magnet-80-Pack-NSN0657/204721317

http://www.amazon.com/Pcs-Neodymium-NdFeB-Disc-Magnets/dp/B011SY1NNO/ref=sr_1_6?ie=UTF8&qid=1437485649&sr=8-6&keywords=1+4+x+1+16+neodymium+magnets

https://www.kjmagnetics.com/proddetail.asp?prod=D41

There are 5 files for this model, detailed below:

PRINT INSTRUCTIONS

.....................................................................................................

Lens_BGhost.STL - QTY:1 Suggested Settings: Translucent Aqua PLA, 225*C, 100% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Eye_BGhost.STL - QTY:1 Suggested Settings: Black PLA, 225*C, 100% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Wing_Insert.STL - QTY:4 Suggested Settings: Orange PLA, 225*C, 100% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Horn_BGhost.STL - QTY:4 Suggested Settings: Black PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Dial_BGhost.STL - QTY:1 Suggested Settings: Black PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Winglet_A_BGhost.STL - QTY:4 Suggested Settings: White PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Winglet_B_BGhost.STL - QTY:4 Suggested Settings: White PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Rear_Body_BGhost.STL - QTY:1 Suggested Settings: Black PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Front_Body_BGhost.STL - QTY:1 Suggested Settings: Black PLA, 225*C, 15% fill, 2 shell, 0.12mm layer height, Raft Optional. NO SUPPORTS

Pins.STL Qty: 1

........................................................................................................

Winglets have built-in rafts to aid in keeping the corners stuck down. Trim these off afterwards with a deburring tool or razor blade.

Use good super glue or 2-part epoxy to glue the Neodymium magnets to the body and the inside of the wings. Pay very close attention to the orientation of the magnets so that the correct sides attract each other, double check this before gluing

"Tips" should press fit into the top of the wings.

The black side wing inserts should slide onto the side wings and sort of click into place, glue shouldn't be necessary.

Glue diffuser and black eye-cover onto front of the body. They should fit snug.

Use pins to allign the two halves of the main body. Apply a drop of glue to the holes first to permanently attach them.