Garden Irrigation Spray System / Garten Bewässerung System

Hi

here you will find a garden irrigation system like the manufacturer gardena has. Free under the motto "Why buy, when you can print it" ;-) I have designed it modularly and as GlueEdition so that you can connect different ground holders, middle parts with 1-3 direct connections / gardena coupling or different spray heads. the spray heads are still in development. However, angles of 45°, 180°, 270° and 360° are still available. I was amazed how far the spray head sprays with 2.5 - 3 bar water pressure, so a dosage with a screw in the head is available.

Preview:

https://youtu.be/ruUPSK0xpcE

Support material:

The support material for the spray head is already included in the stl files ( please print the head upside down ). The fine tubes at the place where the o-ring goes in and at the spray exit is can be easily cut out with a cutter knife. For the middle section only support material is required from the base plate.

You need:

• Printed parts ;-)
• Screws 3,5 x12 or 3,5x15
• O-ring inner diameter Ø 12 x 3,5 mm NBR 70 ( https://www.ebay.de/itm/401009056492 )
• M4x 25mm dosage screw

Please note that the development is still in progress. So stay tuned!!!!

Update 31.08.18

• From now on there is a spray head with two 90° opposite exits as some people want. This means that even things opposite each other can be cast. Added:
• sprayhead_v2_9090dg.stl
• sprayhead_v2_9090dgNOdosage.stl

Update 30.08.18

• A GlueEdition is now available. With this, the connections can now be glued to the centre section using acetone. This has two advantages. Anyone can fit any center section with a connector and there is no need to print overhangs. ( No more support needed for the middle section) I have attached some more pictures of the GlueEdition, which I have already tested. Works out great in my opinion. Added:
• middle_section_1con_GlueEdition_v1.stl
• middle_section_2con_GlueEdition_v1.stl
• middle_section_3con_GlueEdition_v1.stl
• middle_section_GE_Connector_Gardena_v1.stl
• middle_section_GE_Connector_Hoseclip_v1.stl
• sprayhead_v1_BlindPlug.stl

Update 11.07.18

• There is now 2 versions of the middle section with clamp connection and Gardena connection, which can be plugged onto a 12mm rod. This means that also higher plants can be sprayed. Added:
• middle_section_StaffHolder_Hoseclip_v1.stl
• middle_section_StaffHolder_Gardena_v1.stl

Update 03.07.18

• I have added some gardena coupling versions to the middle sections. Added:
• middle_section_1con_1gardena_v1.stl
• middle_section_2gardena_v1.stl
• middle_section_1gardena_v1.stl

Update 26.06.18

• I have attached some more pictures of the working system.
• I make the ground holder still a little stronger and with cross struts.
• Now the spray head is available with and without dosing screw. Added:
• ground_holder_v2.stl
• sprayhead_v2_90dgNOdosage.stl
• sprayhead_v2_180dgNOdosage.stl
• sprayhead_v2_270dgNOdosage.stl
• sprayhead_v2_360dgNOdosage.stl

Update 15.06.18

• I have added 90°, 180°, 270°, 360° versions and a dosage option with a screw in all spray heads. Added:
• sprayhead_v2_90dg.stl
• sprayhead_v2_180dg.stl
• sprayhead_v2_270dg.stl
• sprayhead_v2_360dg.stl

Happy printing

MFG

Chris

If you like it ;) https://www.paypal.me/schiffer...