TOOL BOX ORGANIZER (lightweight) SUPPORTLESS PRINT

VARIOUS TOOLBOXES WITH 3D ARTWORK OF CREALITY AND ULTIMAKER inside!

Unlike other tool organizers; Lightweight version included!!! roughly 298 grams, compared to other tool boxes/organizers that weigh over 600+ grams. Heavy weight 582 grams (approximately) also included in this bundle.

8 types/styles of supportless 3D print organizers for holding various parts and tools. Every one of them are supportless even the skeleton (hollow) organizers that take up less filament than the full boxed enclosed ones. The skeleton organizers come with 2 different thickness of stands which are also supportless. One stand being a snug fit (that may require some glue depending on your finished print) and the other stand being a tight fit that might need some sanding to push into the skeleton organizer back end more easier. You only need one stand per skeleton organizer.

**10 files ready to download;

1x non branded enclosed boxed 3D print organizer,

1x non branded skeleton 3D print organiser,

1x non branded with displayed nozzle sizes enclosed boxed 3D print organizer,

1x non branded with displayed nozzle sizes skeleton 3D print organizer,

1x Creality labelled enclosed boxed 3D print organizer,

1x Creality labelled skeleton 3D print organizer,

1x Ultimaker labelled enclosed boxed 3D print organizer. Tick the "print thin walls" box on Cura settings for a higher detail Ultimaker logo.

1x Ultimaker labelled skeleton 3D print organizer. Tick the "print thin walls" box on Cura settings for a higher detail Ultimaker logo.

1x Tight fit stand for all skeleton 3D print organizers. 6-8mm poles. Has a tight fit that might need some sanding depending on your finished print.

1x Snug fit stand for all skeleton 3D print organizers. 5.5-7.5mm poles. May need a drop of glue to hold them in place depending on your finished print.

The organisers holds a variety of tools and parts. Other tools that are not pictured, may be able to fit some where on the organizers.

**Specifications of all organizers:

3x SD Card/Micro Adapter slots (front left level 1),

3x Micro SD card slots (front centre level 1),

2x USB pen drive slots (front right level 1),

13x Nozzle holders that will fit any 6-6.5mm (m6) thread at 20mm deep (all centred on level 2),

1x 27mmx26mm storage slot on right side of the x13 nozzle holders at level 2 (sandpaper storage is attached to it, on the side),

7x Allen key holes on a slope that can hold ranging sizes of 0.89, 1.27, 1.5, 2, 2.5, 3, 4, 5, or 5.5mm (left, next to x3 flat spanner slots on level 3),

1x flat trawl/scrapper up to 44.5mm in width and 1mm thick (left side above the x3 Flat spanner slots),

3x flat spanner slots (pictured left, next to x7 Allen key holes),

3x 44.5x25mm rectangle Holes, 52mm deep. Great for holding different types of pliers (at level 3),

3x 14.5x14.5mm square holes storage slots (at level 3). Mostly used for a wire brushes set etc,

1x 50.5mm diameter circle at 52mm deep (at level 3). Great for assorted storage or a bottle. Can perfectly hold "AprintaPRO" Buildplate cleaner 250ml bottle,

2x 2mm holes for nozzle cleaning needles. One on each corner of level 3,

2x Sandpaper slots on both sides of the organiser,

1x Digital calliper storage hole on the right hand corner of level 4,

1x 62x25mm rectangle hole at 88mm deep (on level 4 top right) for extra storage. Can be used for files, pens tweezers etc,

3x 10mm diameter screwdriver hole/slots at 88mm deep (on level 4),

1x 8mm diameter screwdriver hole/slot at 88mm deep on level 4, between x3 10mm diameter screwdriver hole/slots and the 1x 62x25mm rectangle hole.

**Specifications for all skeleton 3D print organizers not including the stand:

Size: 210.4mm x 165.6mm x 58.9mm (can be re-scaled to any bigger size but will lose its dimensions for some tool compartments. And if you do, you will also have to re-scale the stand to the exact percentage of the re-scaled skeleton organiser).

Print weight on Cura using the settings stated below: approximately 257 grams,
And Cura print time (Ender 5 Plus 40mm/s): approximately 1 days 4 hours and 27 minutes.

Settings (Cura 4.7 using an Creality Ender 5 Plus):
Nozzle size: 0.4
Layer height: 0.2
Initial layer height: 0.2
Wall thickness: 1.6
Wall line count: 4
Top/Bottom thickness: 0.8
Top thickness: 0.8
Top layers: 4
Bottom thickness: 0.8
Bottom layers: 4
Horizontal expansion: 0
Infill density: 20 (you can have a higher infill density for more strength)
Infill pattern: Cubic
Build plate adhesion type: Brim or Skirt (optional)
Generate support: no

**Specifications for all types of stands:

Size: 210mm x 80mm x 88.5mm (can be re-scaled to any bigger size but you will need to re-scale skeleton organiser to the same exact percentage too).

Print weight on Cura using the settings stated below: approximately 41 grams,
And Cura print time (Ender 5 Plus 40mm/s): approximately 6 hours and 6 minutes.

Settings (Cura 4.7 using an Creality Ender 5 Plus):
Nozzle size: 0.4
Layer height: 0.2
Initial layer height: 0.2
Wall thickness: 1.6
Wall line count: 4
Top/Bottom thickness: 0.8
Top thickness: 0.8
Top layers: 0
Bottom thickness: 0.8
Bottom layers: 999999
Horizontal expansion: 0
Infill density: 100
Infill pattern: Cubic
Build plate adhesion type: Brim
Generate support: no

**Specifications for all enclosed boxed 3D print organizers:

Size: 210mm x 140mm x 90mm (can be re-scaled to any bigger size but will lose the dimensions for some tool compartments).

Print weight on Cura using the settings stated below: approximately 582 grams,
And Cura print time (Ender 5 Plus 40mm/s): approximately 2 days 12 hours and 6 minutes.

Settings (Cura 4.7 using an Creality Ender 5 Plus):
Nozzle size: 0.4
Layer height: 0.2
Initial layer height: 0.2
Wall thickness: 1.6
Wall line count: 4
Top/Bottom thickness: 0.8
Top thickness: 0.8
Top layers: 4
Bottom thickness: 0.8
Bottom layers: 4
Horizontal expansion: 0
Infill density: 20 (you can have a higher infill density for more strength)
Infill pattern: Cubic
Build plate adhesion type: Brim or Skirt (optional)
Generate support: no