Undersea Bases Stems and Terrain 28mm

Intended for 3D print.

A collection of undersea-themed utilities and decorations. 22 bases in total, and 7 separate pieces of decoration. Please read detailed list below.

DETAILED LIST

Bases with flying stems

The following is a list of bases with a chain extending upwards. The idea is for you to use these bases as "flying" stems to mount ships, submersible crafts or aquatic creatures on to give them a nautical theme. Support extensions are built into certain bases to prevent imbalance.
Be aware that these bases/stems are experimental in nature. They should work for human-sized miniatures or smaller crafts and creatures, but I cannot guarantee that the bases/stems will be balanced or able to support the weight of any larger miniatures. Use the image gallery to get an idea of how the bases/stems are designed, and try to determine if they are right for your purpose before purchasing. Keep in mind that the models can be be upscaled to accomodate larger miniatures.

• Anchor with chain stem, dragged. Sand Base. No additional support.
• Anchor with chain stem, dragged. Sand Base. With additional (undecorated) support to prevent imbalance.
• Anchor with chain stem, dragged. Sand Base. With additional support to prevent imbalance. Support is decorated to resemble a compass.
• Anchor with chain stem, upright. Skeleton tied to anchor. Sand Base. Bubbles rising from anchor. No additional support.
• Anchor with chain stem, dragged. Stone Base. No additional support.
• Anchor with chain stem, dragged. Stone Base. Compass support.
• Anchor with chain stem, tilted to one side. Skeleton tied to anchor. Sand Base. Bubbles rising from anchor. No additional support.
• Anchor with chain stem, upright. Skeleton tied to anchor. Sand Base. Bubbles rising from anchor. Compass support.
• Anchor with chain stem, tilted to one side. Skeleton tied to anchor. Sand Base. Bubbles rising from anchor. Undecorated support.
• Anchor with chain stem, tilted to one side. Skeleton tied to anchor. Sand Base. Bubbles rising from anchor. Compass support.
• Skeleton sunk to the bottom with concrete weight. Chain Stem wrapped around neck. Compass support.
• Skeleton sunk to the bottom with concrete weight. Chain Stem wrapped around neck. No support.
• Kelp forest with kelp stems separated from base. Print as many as you like and glue to base to create custom kelp forest.
• Kelp forest with numerous kelp stems extending upwards. Small creatures/crafts can be supported by stems. Note that kelp forest may be difficult to clean post-print.

Bases

• Compass Base
• Sand Base, small sand ridge. Can be used with decoration like anchors et cetera.
• Sea Star Base.
• Treasure Chest, closed. Large Base.
• Treasure Chest, closed. Small Base.
• Treasure Chest, opened. Skeleton guarding booty. Large Base.
• Treasure Chest, closed. Skeleton protectively clutching chest. Small Base.
• Treasure Chest, opened. Small Base.

Decoration

• Anchor
• Anchor with chain stem. Skeleton tied to anchor. Bubbles rising from anchor.
• Anchor with chain stem, tilted to one side. Skeleton tied to anchor. Bubbles rising from anchor.
• Anchor with chain stem. Skeleton tied to anchor.
• Anchor. Skeleton tied to anchor.
• Treasure Chest, closed.
• Treasure Chest, opened.

Files are packaged in one .rar archive, with fairly detailed descriptions in file names.

UPDATE 20210810 : Two additional shipwreck models added to megapack.

Objects within the .stl file are pre-scaled to 28mm scale. Depending on the size of your printer, individual model parts may have to be cut out to fit within printer area. Relatively high printer settings are recommended (c.a 0.08mm layer height, 15% infill). Printing time depends on the number of model parts you choose to print at once. A single model part (i.e one 28mm round base with chain stem) takes approximately 3.5 hours to print.