Skip to content

Dual Sense Controller Face buttons and L1/R1 L2/R2 buttons (playstation 5)

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 4.3/5 (4 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 23.3k views
  • 45 likes
  • 281 downloads
  • 2 comments
  • 1 make
License
3D design format
STL and ZIP Folder details Close
  • D-Pad_dualsense_xile6.stl
  • D_Pad_Imprint_multi_color_xile6.stl
  • D_Pad_Imprint_xile6.stl
  • Dualsense_L2_R2_xile6.stl
  • Dualsense_L2_xile6.stl
  • Dualsense_R2_xile6.stl
  • L1_Button_xile6.stl
  • L2_R2_None_imprinted_xile6.stl
  • L2_R2_smaller_imprint_xile6.stl
  • O_Flat_button_dual_sense_xile6.stl
  • O_imprint_xile6.stl
  • O_multi_xile6.stl
  • O_pause_xile6.stl
  • PS5_Bubble_resinTop_xile6.zip
    • Dpad_B_xile6.stl
    • Dpad_L_xile6.stl
    • O_B_xile6.stl
    • O_L_xile6.stl
    • ShorterO_B_xile6.stl
    • ShorterO_L_xile6.stl
    • ShorterSq_B_xile6.stl
    • ShorterSq_L_xile6.stl
    • ShorterTri_B_xile6.stl
    • ShorterTri_L_xile6.stl
    • ShorterX_B_xile6.stl
    • ShorterX_L_xile6.stl
    • SQ_B_xile6.stl
    • SQ_L_xile6.stl
    • tri_B_xile6.stl
    • Tri_L_xile6.stl
    • X_B_xile6.stl
    • X_L_xile6.stl
  • PSLogo_MutliColor.stl
  • PSLogo_MutliColor_Left.stl
  • PSLogo_MutliColor_Right.stl
  • PS_logo_button_xile6stl.stl
  • PS_logo_extended.stl
  • Pause_button_xile6.stl
  • R1_button_xile6.stl
  • ScreenShot_button_xile6.stl
  • Sq_imprint_xile6.stl
  • Sq_multi_xile6.stl
  • Sq_pause_xile6.stl
  • Tri_flat_button_dualsense_xile6.stl
  • Tri_imprint_xile6.stl
  • Tri_pause_xile6.stl
  • X_flat_button_dual_sense_xile6.stl
  • X_imprint_xile6.stl
  • X_multi_xile6.stl
  • X_pause_xile6.stl
  • sq__flat_button_dual_sense_xile6.stl
  • tri_multi_xile6.stl

Learn more about the formats
Last update 2023-01-27 at 04:50
Publication date 2021-02-10 at 20:08
Design number 290618
xile6

xile6

3D printer file info

3D model description

Dual Sense Face buttons and L1/R1, L2/R2 buttons.

Want to customize your controller, not finding any buttons, then this are for you.
Make your controller stand out. Make it your own.

All fully tested and played with for hours to make sure there are no problems.

Trigger Caps only work on BDM-010 controllers with the removable ends

The following is included :

Pause button
Screenshot/Record button
L1/R1 and L2/R2 buttons
Triangle button
Square button
X button
Circle button
PS logo button

For Tri, Sq, X and O buttons :

I have included a few different options for these :

Solid flat top

Imprinted logos (0.4mm imprint in)

Pause at height dual color (Paused around 8.2-8.3mm. I paused and printed one layer of color then swap back. These will have a deeper imprint around 0.8mm)

Multicolored stl (for multicolored printing these will have a flat top no imprinting)

*updated 1/26/23
Resin Top multicolor buttons
(print in multicolor and then add one drop of UV curable resin, cure and then install)

L1 and R1 shoulder buttons.
If you get any sticking with these. File down your top corners of the print (check photos).
Also make sure all supports are 100% removed and cleaned up. The underside of the flat part might need light sanding/filing depending on how your printer handhelds supports. (check photos)

I have some prints stick while others did not after supports removed. So a lightly sand/file if your stick.

L2/R2 trigger buttons.
For removal check photos. There is a small lock tap then they push down.

These are pretty thin so be cause when installing. Once installed they are solid.

PS logo home button :
Single color and multi color print.

LICENSE :

NON-commercial license
NO sharing of the files or mass production.
For personal use ONLY.

*designed around model BDM-010
May or may not fit other models check last photo.

3D printing settings

Print settings :

0.2 or lower layer height for all layers
100% infill for best print
support everywhere
Ironing of top layers to make a smoother top finish. Not need but makes them look better.
On the pause/screenshot buttons be careful removing the support.

MAKE sure ALL support martial has been removed before installing. Light sanding/clipping of the supported bottoms might be needed depending on how well your printer handles supports.

Everything was printed on my MK3 bear printer.

Tags

Advertising

Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, โ€ฆ) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi ๐Ÿ’œ.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.