Hexhog Tabletops: Formidable Fronts Expansion Set
$44.99 Hexhog Tabletops: Formidable Fronts Expansion Set
3D
Published 2021-12-09T16:29:26+00:00
igital file fulfilment for this object will occurr after the end of the Formidable Fronts Campaign finishes its funding period.
This zip file is the Hexhog Tabletop LLC Formidable Fronts release all files prefaced with FF-xxxxxx format. Files provided in standard, hollow, and hollow supported when applicable.
FF-A01-000000-v1 -> Single Tank Trap Flat No Inserts
FF-A02-000000-v1 -> Double Tank Trap Flat No Inserts
FF-A03-000000-v1 -> Triple Tank Trap Flat No Inserts
FF-A04-000000-v1 -> Quad Tank Trap Flat No Inserts
FF-BS2-111110-v1 Small Bunker Part B
FF-BS3-110000-v1 Small Bunker Part C
Files are grouped as follows:
hollow: Component files that have been pre-hollowed. 1.5mm to 2.5mm wall thickness, depending on interior geometry
hollow-supports: Component files that have been pre-hollowed and supported. 1.5mm-2.5mm wall thickness depending on interior geometry
standard: Standard files stls, no hollows, or printer type prep
Important: We strongly reccommend building hills one level at at time as the components are designed to fit snugly and trying to jam a piece in when pieces on layers above it are in place can be a frustrating adventure!
License for our files
Private Use Only
Non Commercial
No Derivatives distribution of any sort.
By downloading files from our MMF page, you are purchasing a non-distribution licence to use these files. You are not purchasing the intellectual property of the files nor the assets used in creating the files.
Do not under any circumstances share these files for free or commercially.
IMPORTANT: Rules, Terms and Conditions
All files and links we share with our backers are meant for you as supporter and no one else. By downloading content made by us (Stl files, Zips. etc), you accept this Agreement and agree to be bound by its provisions. If you do not accept or agree with these terms, do not download the content we provide:
Hexhog Tabletops LLC is the owner of the STL files. The STL files are copyrighted work belonging to Hexhog Tabletops LLC.
Hexhog Tabletops LLC grants you a non-transferable, non-exclusive license to use the files.
You may only use the content provided by us (Stl and their location Links) for personal use, and you are not allowed to distribute or sell them nor the prints.
You can cut/resize our files to fit better your printer or personal needs but you can't share those derivative works (along with the original files).
You can't edit our 3d Files (stl) or use portions of them to create new content for any sort of distribution, sale, or other disbursement.
Our models and miniatures, any other kind of 3d file we release or or portions of our files can't be used in any other project, Kickstarter, Patreon, or any other crowdfunding platform, website, or release.
You can't make molds of our models, reproduction or casting or any kind of mass production is prohibited.
You can take photos, make live streams and video with our printed files (ideally to Showing 3d printer results or painting examples or awesome battler reports!) as long as you state that the models have been made by us. In this case our MyMiniFactory Store / Campaign would be greatly appreciated. Also a courtesy cross-post on our discord channel is appreciated!
All copyrights belong to Hexhog Tabletops, No rights are assigned or transferred to the end-user. Our designs are protected by intellectual property laws.
Revision Notes
01_FF_Standard_v2.zip -> FF-U1-EDGCTL-V2, FF-V02-EDGEVTR-v2, FF-W01-EDGDTL-v2 corrections posted.
We hope you enjoy printing these files. We have grouped printing thoughts into general, FDM, and SLA tips.
General:
All files tagged OpenLOCK are designed for use with OpenLOCK Clips, see below for links to clips:
All hexes have a longest dimension of roughly ~105mm point to point, (slightly less really)
Piece images can be downloaded here.
Get your clips at Thingiverse
OpenLOCK Kit
OpenLOCK Springy Clip
OpenLOCK Magnet Clip
Come on over to our Discord channel to troubleshoot!
FDM Printing:
We have provided some files with integrated print supports you punch out after printing, these files are FDM-supports. We use pliers to remove them. (there are 8 supports per OpenLOCK port).
Recommended orientation is flat to the print bed. (Not on edge!)
We can recommend PLA and ABS, as we have used both.
We typically print in .2mm or .3mm layer height, 5% infill, no supports for FDM
SLA printing:
First as you all know if you have a resin printer, it can be finicky depending on resin type, temperature, and post print cure conditions.
We recommend a less brittle resin, ABS-like or fast are two ways it is described. Standard resins can shatter with forces you see pushing parts together or if you drop pieces.
We have done the most prints with Siraya tech Fast Grey. It prints and cures atand we still get a press fit.
Clear resins can have warping issues from refraction, we have experienced this.
Dust settling into your print bed can cause issues.
Don’t leave resin prints overnight in your ultrasonic cleaner and solution, they will warp!
Keep a exacto knife and sand paper to recover any minor errors you encounter.
If you are experiencing tight fit ups use the extra tolerance file. We adjusted it after feedback to ease fit up. Wehave never used it for our productions as all our resin pieces come out fine, but tight.
Watch out for sun curing the hollow parts with long flat surfaces. You can get warping.
Consider curing detail pieces sitting in a hexbase file if you are worried about warping during cure, we haven’t had to do this but was advice shared we thought we could pass on.
| Date published | 09/12/2021 |
| Price | $44.99 |
Hi the following STLs have some issues - FF-U01-EDGCTL-v1.stl FF-V01-EDGVTL-v1.stl The biggest issue is that they are too tall, meaning that the slot doesn't line up if the clips are connected. They also don't have a flat base, the sculpt for the hill is just slightly higher than the outline of the hex, meaning it won't stick to the build plate of a printer. They are from the Formidable Fronts pack. I would guess all the "Edges and Risers" (which are thrown in as an extension to the HH set) are similarly borked, but I have not tested them all.