Twist Formicarium Modules

Demo:
https://youtu.be/7Vhj8G6GHrY

Here's a new connection method I'm working on for formicarium modules. These modules will be 3/4 to 1 turn screw on to connect modules. There will be a nub at the top of the screw to align and lock the modules when screwed together.

3/8" OD flex tubing should also just fit directly into the female Twist connectors. Connect modules using the 3/8" OD flex tubing or use the Twist male to male adapter.

See pictures.

I recommend printing test tube adapters with a flexible filament such as TPU. I have broken several test tubes using rigid filaments.

Included are adapters for compatibility with "Many Formicarium" connectors. https://www.thingiverse.com/thing:2377968

Test tube adapters are still being designed and tested. 12mm tubes tested. Test prints are being done with PLA. The fitment of the connectors may not be the same with different plastic combinations.

Ideas
- Use Twist Plug to stop any ports up that aren't being used.
- Use cotton or another soft material wrapped around the 3/8" OD vinyl tube and secure 12mm test tube over it.
- Use 12.5mm test tube cap as a cap on a female to female connector (s shown in picture)
- Use 12.5mm test tube cap as connector between female to female connector and test tube (as shown in picture, poke hole in cap)
- Connect two 12.5mm test tubes back to back using test tube caps and female to female connector (poke holes in caps)
- Trim the flanges off the 12.5mm test tube cap to fit the small end into a 1/8" vinyl tube (poke hole in cap). Then join to other twist modules using female to female connector.

This project is now in beta development stage. Exisiting components as of December 31, 2019 should be working.

I appreciate any tips towards my work.

Please comment on your ideas.

Module TypeFile NameFootprintConnector Type


BaseAdvanced Single Base100mm x 60mm3 Twist Female Connectors plus hydration chamber


Base AccessoryHumidity Drawer for Advanced Single BaseHumidity drawer for Advanced Single Base


BaseSingle Base B100mm x 60mmFemale Connector


ChamberTwist Feeding Chamber60mm x 40mmFeeding chamber with one female connector


ChamberSmall Chamber40mm x 34mmRemixed Small Chamber with Twist Connectors


Chamber AccessoryTwist Feeding Cup19mm x 19mmFeeding cup for feeding chamber


AdapterTwist Connector Block 4HConnector block H configuration with 4 female Twist ports


AdapterTwist Connector Block 2iConnector block i configuration with 2 female Twist ports


AdapterTwist Male Connector PlugTwist male connector plug


Adapter12mm OD Tube Male Connector ModuleTwist to Male 3/8 ID tube Connector


AdapterMale Bracket to Twist MaleMale "Many Formicarium" to Twist Male Connector


AdapterMale Bracket to Twist FemaleMale "Many Formicarium" to Twist Female Connector


AdapterFemale "Many Formicarium" To Twist MaleFemale Bracket to Twist Male Connector


AdapterFemale "Many Formicarium" To Twist FemaleFemale Bracket to Twist Female Connector


AdapterTwist Female to FemaleTwist Female to Female v2 Connector


AdapterTwist Male to MaleTwist Male to Male v2 Connector


AdapterTwist Male to 12mm Test TubeTwist Male to 12mm Test Tube Straight Adapter


AdapterTwist Male to 12mm Test Tube 90 Degree LeftTwist Male to 12mm Test Tube 90 degree left adapter


AdapterTwist Male to 12mm Test Tube 90 Degree RightTwist Male to 12mm Test Tube 90 degree right adapter


AdapterTwist Male to 12mm Test Tube 90 Degree UpTwist Male to 12mm Test Tube 90 degree up adapter


AdapterTwist Male to 16mm Test Tube 90 Degree LeftTwist Male to 16mm Test Tube 90 degree left adapter


AdapterTwist Male to 16mm Test Tube 90 Degree RightTwist Male to 16mm Test Tube 90 degree right adapter


AdapterTwist Male to 16mm Test Tube 90 Degree UpTwist Male to 16mm Test Tube 90 degree up adapter




Make your own module!

Please share!


ConnectTwist Female ConnectorUse to design your own module. Place lock notch at top.


ConnectTwist Male ConnectorUse to design your own module. Place lock notch at the top.

-