AAP01 modern kit with Holster

Modern KIT for AAP with holster. Lock release is below the Thumb. Holster is compatible with rotary style pads from IMI or similar, or you can download my IMI/Safariland QLS adapter.

IMPORTANT: READ LIST OF PARTS AND INSTRUCTIONS BEFORE YOU BUY THIS KIT, IT WILL NOT WORK WITH STOCK AAP
- Printer build plate volume, in X or Y must have 190 mm, this kit is printed FLAT
- Parts are already oriented for printing.
- KIT is with TDC Mod files, but there is second main body withoud a TDC MOD hole.
- Holster can be used with tracer units or silencer as long external diameter is not larger than 30 mm
IMPORTANT Holster is designed to work with Olight Valkyrie PL-PRO TORCH, Surefire is longer and have latch for battery compartment below, while you COULD technically holster it, lock mechanism will not engage and you can accidentally open battery compartment

Im planning to make Holster taht is compatible with Surefire X300 Torch in the future.

List of Parts Needed:
- Upper Receiver Connector for AAP01
- Outer barrel extender 18 mm x 85 mm (can be a little wider, but not more than 18,8 mm)
- Steel Spring - 12 mm lengh / 4,5 mm diameter

Screws and bolts in mm standards:
- DIN Standards and measurements:
link
link
link
link

For the AAP replica Kit
DIN 7991 - Hexagon socket countersunk head cap screws
- M3x8 x1 (Rear sight, front one)
- M3x10 x1 (Rear sight, rear one)
- M2,5x6 x1 (Front sight)
DIN 912 - Hexagon socket Head Cap Screws
- M5x16 - x1 (Back piece KIT) (IMPORTANT 16 mm lengh of the thread needed, to long may damage your fire selector, to short may damage your BBU thread if use to much force, to be sure remove fire selector and check if the tip of the screw is flush with internat wall of the BBU)
-M4x14 x1 (Front)

DIN 934 - Hexagon Nuts
- M4 x1 (Front)
- M2,5 x1 (Front sight)

For Holster
DIN 7991 - Hexagon socket countersunk head cap screws
- M3x12 or 14 x1 (Lever rotation)
- M3x25 x1 (Lock rotation)
- M3x16 x1 (Lever Lock release/pusher)

DIN 912 - Hexagon socket Head Cap Screws
- M4x50 x2 Lower holster

DIN 934 - Hexagon Nuts
- M3 x2 (Lever Rotation and Lever Lock release/pusher)
- M3 Slim type x 1 (Lock rotation) (1,7 mm m parameter, you can use normal one if needed)
- M4 x3 (lowe holsetr part and rotary locking system, IMI systems (see descritpion) or QLS adapter (see my other uploads)

For TDC MOD
DIN 913 - Hexagon socket set screws with flat point
M4x4 TDC Mod

PRINT SEETINGS USED and print Info (I use Prusa Slicer) ,Printed KIT on Prusa MK3S
RECOMMENDED PRINT MATERIAL ESUN PLA+ (plain PLA can be to stiff and brittle, do not print with PETG definetly to brittle, some parts will break, already tested)
ADHESION I use BuildTak pads on steel spring sheets, so be sure that your adheasion is exelent, if some parts warped from bed, means that adhesion was not good enough.
do not use textured bed plates only smooth ones
- Layer Height 0.16
- bottom and upper layers x 14
- Perimeters x 5 at least
- Infill 20% (exept For Lever and lock mechanism, they should be 100%)
- Cooling: use autocooling with min 60% and 100% max for overhangs and very short layers, for better layer adhesion
- Supprts YES (but not auto, use brush and smart fill in PrusaSlicer)
TOP contact distance for supports 0.16 for better removal with 2 Interface loops
BOTTOM contact distance for supports 0.2 for better stability with 2 interface layers
Support Separation from object 75%
On request If needed i can provide my settings for Prusa Slicer ( for use with Prusa MK3S printers)
- Brim: yes but i use only one pass, more for cleaning nozzle.
- Recommend Use of Ironing for all top surfaces for better finish (or you can sand them later)
In some places after print some sanding may be required. Depends on your printer setup.