Skip to content

KAMAZ universal platform

Фото-21.05.2023,-15-14-04.jpg KAMAZ universal platform
kamaz-short_-_SD_480p.webp KAMAZ universal platform
Фото-21.05.2023,-15-16-06.jpg KAMAZ universal platform
Фото-21.05.2023,-15-23-17.jpg KAMAZ universal platform
Фото-21.05.2023,-15-14-52.jpg KAMAZ universal platform
Фото-21.05.2023,-15-09-53.jpg KAMAZ universal platform
Фото-05.05.2023,-22-32-47.jpg KAMAZ universal platform
Фото-21.05.2023,-15-24-20.jpg KAMAZ universal platform
Фото-29.05.2023,-23-08-43.jpg KAMAZ universal platform
Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5.0/5 (1 vote)
Evaluation of members on the printability, utility, level of detail, etc.
  • 1.4k views
  • 3 likes
  • 50 downloads
License
3D design format
ZIP Folder details Close
  • kamaz-universal-platform.zip
    • asm-v1.0.5.pdf
    • axle/axlerear-shaftlong-left.stl
    • axle/axle-back-cover-servo.stl
    • axle/axlerear-baselong-screws.stl
    • axle/axle-base-cover.stl
    • axle/axlerear-base-screws.stl
    • axle/axlerear-b-out.stl
    • axle/wheel22rear.stl
    • axle/diff-base.stl
    • axle/axlerear-shaftlong-right.stl
    • axle/axle-gear-small.stl
    • axle/wheel22.stl
    • axle/axlerear-b-in-holder.stl
    • axle/axlerear-shaft-right.stl
    • axle/diff-lock-bushing.stl
    • axle/diff_gear_side.stl
    • axle/steering-pasv.stl
    • axle/axle-middle-shaft.stl
    • axle/wheehub-int-dn.stl
    • axle/axlerear-b-out-washer.stl
    • axle/axle-middle-shaft-cardan-nail.stl
    • axle/axle-bushing.stl
    • axle/axle-middle-shaft-cardan.stl
    • axle/axle-back-cover-noservo.stl
    • axle/axle-shaft-left.stl
    • axle/diff-gear-big.stl
    • axle/axle-base-main.stl
    • axle/axlerear-base-nuts.stl
    • axle/axlerear-shaft-left.stl
    • axle/axle-input-cover2.stl
    • axle/wheelhub-ext-nuts.stl
    • axle/diff-washer.stl
    • axle/axle-gear-big.stl
    • axle/axlepasv-base-main-nuts.stl
    • axle/axlerear-b-in-washer.stl
    • axle/wheelhub-int-up.stl
    • axle/steering.stl
    • axle/axle-gear-hex-2.stl
    • axle/axlerear-baselong-nuts.stl
    • axle/axle-gear-hex-1.stl
    • axle/wheehub-arm.stl
    • axle/diff_gear_wheel.stl
    • axle/diff-gear-small.stl
    • axle/axle-shaft-right.stl
    • axle/steering-servo-arm.stl
    • axle/steering-arm-pasv.stl
    • axle/axle-input-shaft.stl
    • axle/wheel38.stl
    • axle/axle-input-cover.stl
    • cabin/fender-back-bumper.stl
    • cabin/frame-mount-extra (Mirror).stl
    • cabin/cabin-side.stl
    • cabin/frame-mount-extra.stl
    • cabin/mirror-holder.stl
    • cabin/cabin-lock.stl
    • cabin/front-attachment-mount2.stl
    • cabin/cabin-front.stl
    • cabin/bumber-frame-mount-side.stl
    • cabin/fender-short.stl
    • cabin/bumper-side.stl
    • cabin/cabin-back-extra-arduino.stl
    • cabin/bumper-side(Mirror).stl
    • cabin/cabin-back.stl
    • cabin/mirror.stl
    • cabin/cabin-side (Mirror).stl
    • cabin/fender-back-bumper (Mirror).stl
    • cabin/cabin-mount.stl
    • cabin/cabin-top.stl
    • cabin/bumper-center.stl
    • cabin/front-attachment-mount.stl
    • cabin/front-attachment-mount (Mirror).stl
    • cabin/cabin-mount (Mirror).stl
    • cabin/mirror (Mirror).stl
    • cardan/cardan70-int.stl
    • cardan/cardan60-int.stl
    • cardan/cardan70-ext.stl
    • cardan/cardan60-ext.stl
    • cardan/cardan90-int.stl
    • cardan/cardan80-int.stl
    • cardan/cardan80-ext.stl
    • cardan/cardans.f3d
    • cardan/cvjount.stl
    • frame/frame30x100.stl
    • frame/bamper-mount (Mirror).stl
    • frame/frame80.stl
    • frame/frame30x160.stl
    • frame/frame120.stl
    • frame/frame30x140.stl
    • frame/frame30x80.stl
    • frame/bamper-mount.stl
    • frame/frame30x120last.stl
    • frame/frame-en.stl
    • frame/frame-st.stl
    • frame/frame30x120.stl
    • frame/frame160.stl
    • frame/bamper.stl
    • gb/bushing17.5.stl
    • gb/covernew-mid.stl
    • gb/gear-red1.stl
    • gb/covernew4-output.stl
    • gb/gt2_t37_input2.stl
    • gb/output-shaft-cover.stl
    • gb/gear-first-wlock.stl
    • gb/gear-second-wlock.stl
    • gb/lock.stl
    • gb/covernew-filler-in.stl
    • gb/covernew4-shaft-line.stl
    • gb/gear-rev2.stl
    • gb/output-shaft.stl
    • gb/gt2_t35_input2.stl
    • gb/gear-second1.stl
    • gb/gt2_t36_input2.stl
    • gb/shaft-rev.stl
    • gb/covernew4-input.stl
    • gb/covernew-filler-out.stl
    • gb/gear-third1.stl
    • gb/shaft-red.stl
    • gb/bushing1.25.stl
    • gb/gear-rev-wlock.stl
    • gb/gear-second2-bushing.stl
    • gb/gt2_t34_input2.stl
    • gb/bushing22.5.stl
    • gb/lock(Mirror).stl
    • gb/gear-third-wlock.stl
    • gb/gt2_t31_input1.stl
    • gb/covernew-servo-holes-cover.stl
    • springs/springsrear-layer4.stl
    • springs/frame-springs-holder6.stl
    • springs/springsrear-layer5.stl
    • springs/springsrear-layer3.stl
    • springs/frame-srpings-holder4.stl
    • springs/frame-srpings-holder2.stl
    • springs/frame-srpings-holder3.stl
    • springs/axlerear-springs-holder.stl
    • springs/frame-srpings-holder1.stl
    • springs/springsrear-holder1.stl
    • springs/axle-front-spring-layer2.stl
    • springs/axle-front-spring-layer3.stl
    • springs/springsrear-holder2.stl
    • springs/axle-front-spring-layer1.stl
    • springs/frame-srpings-holder4-m.stl
    • springs/springsrear-holder3.stl
    • springs/axle-front-spring-layer4.stl
    • springs/springsrear-holder4.stl
    • springs/springsrear-holder5.stl
    • springs/axle-front-spring-holder.stl
    • springs/frame-srpings-holder3-m.stl
    • tank/tank-bumper.stl
    • tank/tank-mount.stl
    • tank/tank-powerbank-back.stl
    • tank/tank-mount-long.stl
    • tank/tank-powerbank-mid.stl
    • tank/tank-powerbank-top.stl
    • tc5/output-shaft-cover.stl
    • tc5/tc5-cover-out.stl
    • tc5/tc5-output-cardan-nail.stl
    • tc5/tc5-shaft-output.stl
    • tc5/tc5-gear.stl
    • tc5/tc5-shaftnew-input.stl
    • tc5/tc5-bushing8x1.75.stl
    • tc5/tc5-cover-in.stl
    • tc5/tc5-filler.stl

Learn more about the formats
Publication date 2023-09-14 at 10:38
Design number 1449428
aklin

aklin

3D printer file info

3D model description

Allows you to make a two/three/four-axle model with rear/all-wheel drive.

Scale 1:12

Platform plus dumptruck extension video:
https://youtu.be/al39zDhI0Jw

THIS MODEL IS KAMAZ ONLY!
DUMP EXTENSION: buy

The total length of the frame can be arbitrary, varies in 20mm increments, with some restrictions on minimum dimensions.

Almost everything is printed, except fasteners, bearings, electronics (including batteries, motor and servos), tires and small things like plexiglass, ropes and rubber bands with zip ties.
Printed axles, cardans, transfer case.
321R gearbox controlled by two servos

Functional model, not a copy (not highly detailed)

Assembly guide and notes, 65 pages

approx shoplist

No fusion 360 files included

Backhoe project is here (https://www.thingiverse.com/thing:5539326)

Sizes 590x210x270mm, 5.2kg total
240hours of printing, 1.8kg black abs, ~1.0kg orange abs, 110gr petg for gears

3D printing settings

FRAMES: 4 perimeters, 5 top/bottom, 50% infil
OTHERS: 2 perimeters, 3 top/bottom, 20% infil
0.4 nozzle, 0.25 layer

I print from chip ABS, gears are PETG
I don't print with other materials much, and I can't say how well other materials are suitable for this project. But there should not be any special problems.

Tags

Advertising

Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi 💜.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.