This is a tool that facilitates the gluing of 1/8 scale wheels. The tool includes a protective ring for the mousse that can be removed.
The tool is prepared to support more scales in the future.
You can test to see if your wheel is compatible with the mousse protection. If it is not, let me know and I will see what I can do.
https://www.cgtrader.com/free-3d-print-models/hobby-diy/hand-tools/design-a-outer-diameter-test-prueba-de-diametro-exterior
This design needs the following:
Screws: 1x M3*50mm, 1x M3*30mm. Nut: 2x M3, 1xM5
ESPAÑOL
Esta es una herramienta que facilita el pegado de ruedas de escala 1/8. La herramienta incluye un aro de protección para la mousse que se puede retirar.
La herramienta esta preparada para soportar mas escalas en el futuro.
Puede hacer un test para comprobar si su rueda es compatible con la protección para la mousse. Si no lo es, informeme y vere lo que puedo hacer.
https://www.cgtrader.com/free-3d-print-models/hobby-diy/hand-tools/design-a-outer-diameter-test-prueba-de-diametro-exterior
This design needs the following:
Screws: 1x M3*50mm, 1x M3*30mm. Nut: 2x M3, 1xM5
Printing parameters / PARÁMETROS DE IMPRESIÓN 3D;
-Base
Material: PLA/PETG,etc.
Layer height 0.3 or less.
Filling: grid,30% or higher. Wall loops 3 or higher, top or bottom layer 4.
Support: Yes. Supports only on the base.
-Close
PLA/PETG material,etc.
Layer height 0.3 or less.
Filling: Grid, 40% or higher. Wall loops 3 or higher, top or bottom layer 4.
Support: No
-Beader
PLA/PETG material, etc.
Layer height 0.3 or lower.
Filling: Grid,30% or higher. Wall loops 3 or above, top or bottom layer 4.
Supports: No.
-axis
Material PLA/PETG,etc.
Layer height 0.3 or less.
Filling: Grid, 40% or higher. Wall loops 3 or higher, top or bottom layer 4.
Support: NO Raft: YES
***** If you are going to use the tool outdoors or in areas with temperatures above 30º it is recommended to print on ABS or ASA.
ESAPAÑOL
Parametros de impresión:
-Base
Material: PLA/PETG,etc.
Altura de capa 0,3 o inferior.
Relleno: rejilla,30% o superior. Bucles de pared 3 o superior, capa superior o inferior 4.
Soporte: Si. Soportes solo en la base.
-Cierre
Material PLA/PETG,etc.
Altura de capa 0,3 o inferior.
Relleno: Rejilla, 40% o superior. Bucles de pared 3 o superior, capa superior o inferior 4.
Soporte: No
-Pestillo
Material PLA/PETG,etc.
Altura de capa 0,3 o inferior.
Relleno:Rejilla,30% o superior. Bucles de pared 3 o superior, capa superior o inferior 4.
Soportes: No.
-Eje
Material PLA/PETG,etc.
Altura de capa 0,3 o inferior.
Relleno: Rejilla, 40% o superior. Bucles de pared 3 o superior, capa superior o inferior 4.
Soporte: NO Balsa: SI
***** Si va a hacer uso de la herramienta en exteriores o en zonas con temperaturas superiores a 30º es recomendable imprimir en ABS o ASA.