Robot Claw Phone Holder

Why pay for this single file when you have it + over 500 more for a lot less? That’s right. STLFLIX is a multi-theme ever-growing library of STL files. Your One-Stop-Shop for Premium 3D-Printing models. Get started with the Ultimate STL platform!

Click here to join STLFLIX

Robot Claw Phone Holder

This STL file is recommended for FDM Printers!
3D Printing Time: 1Day 23 Hours and 3 Minutes
Approximately length: 39cm x 18cm x 18cm

The future is here and it holds your phone for you. How awesome is that?

This model has a steady locking system, it's adjustable and you don't have to use any supports for printing! For instructions, check the assembly video.

Check the assembly instructions below:

Start with "Robot Claw Phone Holder_base".

Attach "Robot Claw Phone Holder_Lower_Arm_Long" on top of the base.

Next, insert "Robot Claw Phone Holder_Screw_3" between the two previous pieces.

Place "Robot Claw Phone Holder_Quick_Release_Clip_1" on top of "Robot Claw Phone Holder_Screw_3" and fold it until it applies pressure.

Attach "Robot Claw Phone Holder_Upper_Arm_Long" on top of "Robot Claw Phone Holder_Lower_Arm_Long" and secure them together using "Robot Claw Phone Holder_Screw_2".

Attach "Robot Claw Phone Holder_Quick_Release_Clip_2" and fold it until it applies pressure.

Attach "Robot Claw Phone Holder_Wrist" on top of "Robot Claw Phone Holder_Upper_Arm_Long" and secure both pieces using "Robot Claw Phone Holder_Screw_1".

Place "Robot Claw Phone Holder_Quick_Release_Clip_1" and fold it until it applies pressure.

Separately, attach "Robot Claw Phone Holder_Left_Finger" and "Robot Claw Phone Holder_Right_Finger" to the pins of "Robot Claw Phone Holder_Hand".

Next, place "Robot Claw Phone Holder_Middle_Finger" in the middle.

Then, attach "Robot Claw Phone Holder_Cover" and twist it until it locks.

Finally, attach this entire piece to "Robot Claw Phone Holder_Wrist".

Adjust the pressure and position using the clips. Adjust them as desired!

The smaller version follows the same assembly instructions, with the only change being the parts "Robot Claw Phone Holder_Lower_Arm" from "_Long" to "_Short" and "Robot Claw Phone Holder_Upper_Arm" from "_Long" to "_Short".

COPYRIGHT & SELLING RIGHTS

This STL file is copyrighted by STLFLIX©, the Ultimate STL Subscription. This means you can print it for yourself, but you DO NOT have the right to sell it.

To acquire copyright & selling rights, you must subscribe to our Commercial License. By doing so, you will also get immediate access to over 500 STL files, unlimited downloads, and marketing content for every single file.

Go commercial and skyrocket your own store with STLFLIX!

GO COMMERCIAL!

USEFUL LINKS

Get to know us a little better!

Website | Instagram | TikTok | Twitter

What are you waiting for? Join thousands of other makers from all around the world.

HAPPY PRINTING!

Line Width/ Nozzle: 0.4 mm
First Layer Line Width: 0.48 mm / 120%
Average Speed: 20mm/s (First Layer) / 60mm/s (All the other layers) / 20 mm/s (First Layer) / 500 mm/s (All the other layers on Bambu Lab)
Recommended Initial Layer Height:  0.2 mm
Recommended Layer Height:  0.2 mm
Recommended Perimeters/ Walls: 3.
Recommended Infill (%): 10% (Gyroid)
Needs Support: No.
Build Plate Adhesion: Skirt.

The parameters above are recommendations made by our staff; if you prefer, you can adapt them according to your preferences.