Skip to content

FMS ATLAS 6WD WITH 6th WHEEL AND SEMI TRAILER

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 4.5/5 (2 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 1.7k views
  • 5 likes
  • 8 downloads
  • 1 comment
License
3D design format
STL Folder details Close
  • 5th wheel 2 base.STL
  • 5th wheel 2 front part .STL
  • 5th wheel 2 hinge x2 .STL
  • 5th wheel 2 lower swivel.STL
  • 5th wheel 2 rear parts .STL
  • 5th wheel 2 screw locker.STL
  • Fms Atlas semiV2 axle x2.STL
  • Fms Atlas semiV2 bumper rear.STL
  • Fms Atlas semiV2 front reinforcement inner x2.STL
  • Fms Atlas semiV2 front reinforcement outer x2.STL
  • Fms Atlas semiV2 leaf spring SOFT x2.STL
  • Fms Atlas semiV2 leaf spring SUPER SOFT x2.STL
  • Fms Atlas semiV2 leaf spring fixture x4.STL
  • Fms Atlas semiV2 leaf spring x2.STL
  • Fms Atlas semiV2 main frame front sliding plate.STL
  • Fms Atlas semiV2 main frame front.STL
  • Fms Atlas semiV2 main frame junction rail x2.STL
  • Fms Atlas semiV2 main frame middle.STL
  • Fms Atlas semiV2 main frame rear.STL
  • Fms Atlas semiV2 panel front left.STL
  • Fms Atlas semiV2 panel front right.STL
  • Fms Atlas semiV2 panel front.STL
  • Fms Atlas semiV2 panel middle left.STL
  • Fms Atlas semiV2 panel middle right.STL
  • Fms Atlas semiV2 panel rear left.STL
  • Fms Atlas semiV2 panel rear locker Left.STL
  • Fms Atlas semiV2 panel rear locker right .STL
  • Fms Atlas semiV2 panel rear right.STL
  • Fms Atlas semiV2 panel rear.STL
  • Fms Atlas semiV2 park leg locker x2.STL
  • Fms Atlas semiV2 park leg x2.STL
  • rim traile 17mm tire inner ring.STL
  • rim traile 17mm tire inner.STL
  • rim traile 17mm tire outer.STL

Learn more about the formats
Publication date 2023-11-12 at 10:39
Design number 1573182
lulu3Dbuilder

lulu3Dbuilder

3D printer file info

3D model description

Since a while I wanted to get a semi trailer on the FMS ATLAS without compromising the crawling capacity of this fantadtic truck.
Then I had to find a way to let the 5th wheel move also from side to side.
Capacity have to be significant too then I made the trailer 410mm long and 115mm width. The 5th wheel is fitted as low as possible on the truck but the semi was to high for me then I lowered a bit the rear section to get the trailer wheels not so far from the structure.
The trailer structure is made from the swivel trailer you have seen, then it is 2 times the length of a swivel trailer.
Two rear axles are linked together with articulated leaf springs alowing rotation from the midel of the wheels. It is easy to assemble and give nice movement of the axles when offroading.
As you can see in pics the trailer allow to carry scx24 crawler if you want or any other stuffs. I think you can even carry beer cans to deliver to your friends.
Trailer has 2 parking feet you can retract and lock when driving.

Assembly is not very difficult, there are 3 main parts for the complete length you have to glue together. For the 2 front parts just glue and glue some junction parts and for the rear section there are 2 corners you can glue or screw. Screwing is not easy but possible as I did.
I suggest to fit first on all section the side panels to locate correctly the main parts together and get side panels aligned.

As usual you have to redrill holes to 1.2mm when a screw has to screw in and redrill to 1.5mm when a screw has to go through freely. Use M1.4 screws from 4mm to 12mm for the whole assembly.
You need a M3 x 8mm screw for the fitting point into the 5th wheel.
You have 3 different leaf springs but I suggest to start with the super soft. Others are really rigid
Tires are Jeep wrangler SCX24 tires with 55mm diameter you can find on Aliexpress and probably ebay too.
They are fitted on dedicated rims which are the same as for swivel trailers.
Concerning the 5th wheel, it can rotate in 2 directions which is a good improvement for crawling.
You need a M2x 20mm or any 2mm stud for the lateral rotation.
A locker is made with a M2 x 30mm screw or any 2mm stud. when lock you cannot release the trailer from the truch in any way, unless you remove this stud. I drilled the hole for this stud in the 5th wheel to 2mm then the screw or stud can be fitted and remove easily.
5 the wheel is in 3 parts to get a good sliding surface. The trailer receive a separate part you need to glue on with the side you printed on the bed of the machine in contact with the 5th wheel.
I had a lot of fun making this combo and I hope you will enjoy it too.
biggest part is 209mm long,

In case of any trouble or request please send Email to luc.tellier@wanadoo.fr

Videos below

https://youtu.be/hm2Mf1ZLeFk
https://youtu.be/V3MHGUbRMp4
https://youtu.be/z2H7vHdOvNg

3D printing settings

Nothing special, 50Β°C bed and 210Β°C nozzle, speed 60mm/s
Printed in PLA as usual

Tags

Advertising

Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi πŸ’œ.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.