PROJECT MILES MORALES PS5 mask with four lenses for 3D printing

Hi everyone !!!
I'm glad to present you my files for the assembly of the mask
MILES Morales from the PS5 game.
You do not buy a ready-made mask
You buy files for 3 d printing
!!!Attention Attention Attention Attention Attention !!!!
This is very important information read it before buying files
All files are in an archive
To unpack them use an archiver on your PC or phone, if you don't have one, you can download them here.
https://www.7-zip.org/
The links are not active, copy them in your browser in the link bar.

1) You are not buying a ready-made mask.
2) You are buying files for 3D printing.
3) There is no tutorial yet, so the files should be bought only by experienced people who have already built my masks.
4) Do not print FACE SHELL with RED PLASTIC.
The IR sensor does not work well with red plastic.
5) DO NOT CHANGE THE FILE SIZE WHEN PRINTING .
ALL FILES ARE ADJUSTED TO OTHER FILES and if you change the size other parts will not work correctly.
6) In this project I have made grooves for battery compartments, switches, made an area for IR diodes and a hole for its mounting
7) Included with the files you will find mini instructions in the form of photos and renderings with captions that should facilitate your process of assembling the mask.
You are not buying a ready-made mask.
You are buying 3D printable files

What is included in the kit
3D files for printing on a 3D printer
1) 1_FACE SHELL folder number 1
a) Contains the MILES Morales mask in one piece.
b) Also contains the same mask but divided into 2 parts.
c) mini manual with cura settings
2) 2_LENSES second folder contains
a) main lenses (these lenses have an almost invisible bar to ensure that the whole lens is placed on the supports and printed more correctly)
b) movable lenses 4 left and 4 right lenses
c) lens retainer in different sizes
d) screw caps
3) 3_Mechanism this folder contains the mechanism
a) rods that are attached to the movable lenses and move them, left and right.
b) mechanisms for servos of two kinds
(for MG90S) and for (SG90).
Also there are two versions of the slides, different sizes so that you will have less to handle them
4) 4_Arduino ( sketch , wiring diagrams )
a) folder with arduino file
b) folder with instructions on what servos, arduino and wires I use
c) renderings of wiring diagrams and elements
d) instructions how to load sketch for NANO and Pro Mini arduinos
5) 5_Other (IR system, covers, molds, holders)

Unfortunately there is no tutorial yet, but you can use this tutorial where I have already made a similar mechanism with four lenses.
The links are not active , copy them into your browser in the link bar.

https://www.youtube.com/watch?v=V-8i2VyCQeg

You can also see how the Miles Morales mask works on my instagram.

https://www.instagram.com/alexironman_3/?hl=ru

Links are not active , copy them into your browser in the link bar.

Tools and materials you will need to create a Spider-Man Away From Home.

1) 3D printer (I use a 3D printer with a print area of 300x300x400) you can use a printer with a standard size of 220x220x250.
2) computer
3) pliers
4) insulation cleaner
5) file
6) utility knife or scalpel
7) wire cutters
8) scissors
9) screwdriver
10 hair dryer
11) soldering iron with a fine tip and power setting
12) tin with solder
13) sandpaper p 320 and p80

/////// glue//////

1) hot glue gun
2) rubber based glue
3) cyanoacrylate glue

////// other//////

1) transparent plastic 1 mm thick / size 15x15 cm
2) perforated film / 20x20 cm
3) eva foam 1-3 mm thick / size 10x15 cm
4) m3 tapered screws . ( 12 pcs. of 8 mm . 10 pcs. of 10 mm . 3 pcs. of 16 mm ) two M3 nuts .

////////////////////////////////////////////////////////////

ELECTRONICS REQUIRED FOR ASSEMBLY

1) arduino nano or pro mini

2) IR sensor HW-201 2 pcs.

3) IR diodes Tcrt5000L 2 pcs.

4) 10K resistor 1 pc.

5) Toggle switches SS12D00G3 2 pcs.

6) Servos MG 90s 2 pcs. or SG90 2 pcs. (I recommend to take MG 90s, they have metal gears and are more powerful).

7) Battery compartment for 2 AAA batteries 2 pcs.

8) 4 AAA 1.5 volt batteries (I recommend getting 4 rechargeable batteries / AAA 1.2 volt 1100 milliampere size and a battery charger)

9) wires (wires can be removed from usb cord, look for soft cord)

///////////////////////////////////////////////////

Links to accessories (all electronics I bought on aliexpress)
Links are not active , copy them in your browser in the line for links
1) arduino nano https://aliexpress.ru/item/4000579100527.html?_ga=2.254829007.656017014.1635797113-1882972174.1630166606&sku_id=10000014886252353&spm=a2g39.orderlist.0.0.47814aa623cHKw
Arduino pro mini https://aliexpress.ru/item/4000928254221.html?_ga=2.142151922.1531354347.1646564291-1882972174.1630166606&sku_id=10000011264046298&spm=a2g39.orderlist.0.0.5c0f4aa6jvomRA

2) сервопривода https://aliexpress.ru/item/4000550040897.html?_ga=2.42012773.1531354347.1646564291-1882972174.1630166606&item_id=4000550040897&sku_id=10000015273780367&spm=a2g39.orderlist.0.0.5c0f4aa6jvomRA

3) IR sensor HW-201 2 pcs.
https://aliexpress.ru/item/4001294541207.html?_ga=2.254829007.656017014.1635797113-1882972174.1630166606&sku_id=10000015650371288&spm=a2g39.orderlist.0.0.47814aa623cHKw

4) IR diodes Tcrt5000L 2 pcs.
https://aliexpress.ru/item/32943225407.html?_ga=2.254829007.656017014.1635797113-1882972174.1630166606&sku_id=66184654299&spm=a2g39.orderlist.0.0.47814aa623cHKw

5) 10K resistor
https://aliexpress.ru/item/32952657927.html?_ga=2.254829007.656017014.1635797113-1882972174.1630166606&item_id=32952657927&sku_id=66353322918&spm=a2g39.orderlist.0.0.47814aa623cHKw

6) Toggle switches SS12D00G3 2 pcs.
https://aliexpress.ru/item/32964400942.html?_ga=2.254829007.656017014.1635797113-1882972174.1630166606&sku_id=66549810542&spm=a2g39.orderlist.0.0.47814aa623cHKw

7) Perforated film (can be purchased from an advertising agency)
https://aliexpress.ru/item/32390585651.html?sku_id=65253896848&spm=a2g2w.productlist.search_results.8.a6e66b40XjmR35
I did not buy the perforated film from this link, so read the reviews carefully.

If you have any questions or concerns, I am available to help you. If you find any problems with the files, I would appreciate it if you let me know!!!

face cover printing. nozzle 0.6 , layer height 0.3 , PEtg gray plastic , nozzle temperature 220-240 , table temperature 60

other printing nozzle 0.4 , layer height 0.2 , plastic PETg any color .