3D model description
IMPORTANT: READ LIST OF PARTS AND INSTRUCTIONS BELOW BEFORE YOU BUY THIS KIT, IT WILL NOT WORK WITH STOCK AAP
MANDATORY: READ MANUAL BEFORE YOU START TO PRINT OR ASSEMBLY THIS KIT
IMPORTANT: THIS KIT REQUIRE WORK, ITS NOT READY TO BE USED JUST AFTER THE PRINT
- !!!BE AWARE THAT THIS KIT REQUIRE YOU TO MODIFY THE BBU AND MAGAZINE!!!
- Printer build plate volume in X or Y must have 25×21×21 cm (9,84"×8,3"×8,3") like PRUSA MK3S, OR build plate big enough to print longest part at angle ( 270 mm) ,this kit is printed FLAT
- Parts are already oriented for printing. Some have prebuild supports that need to be removed after print and print need to be cleaned/ sanded
- KIT is with TDC Mod files
- Two types of main body and front guard
- Three types of stock / stock adapters (Viper stock on photo is not the part of the kit)
- Hex patterns to print if you like the looks
- Silencer is just a tube for Xortech Tracer unit, just for looks, if someone wants it, just sent me a message.
- Kit Works with SRC SR4 ST FALCON Mid-cap 110 bbs, i noticed that Valken also is making mags that looks exactly the same (Valken SMG Mid-cap 110 bbs)
List of things Needed:
- AA Upper Receiver Connector for AAP01
- Outer barrel extender 18 mm x 135 mm (can be a little wider, but not more than 18,8 mm, can be a little shorter, depends of the version of the body and front guard you chose) or longer if you don’t want to use Silencer (silencer should not be wider than 40 mm).
WE G17 normal length mag (need to be modified, see info in manual)
Action Army HPA tap adapter ( you can always try to use different brand, but I cant guarantee that it will fit without modification to the adapter itself).
Steel Spring x4 - 12 mm length / 4,5 mm diameter
Screws and bolts in mm standards:
- DIN Standards and measurements:
link
link
link
link
All Screws and Nuts for whole KIT (With angled grip and magwell
DIN 7991 - Hexagon socket countersunk head cap screws
- M3x12 mm– x6
- M3x14 mm- x6 ( x2 two to lock the BBU)
- M3x16 mm- x6
DIN 912 - Hexagon socket Head Cap Screws
- M5x10 - x1 (Back piece KIT) (IMPORTANT 10 mm length of the thread needed, to long may damage your fire selector, to short may damage your BBU thread if use to much force, to be sure remove fire selector and check if the tip of the screw is flush with internal wall of the BBU)
- M3x10 mm- x1 (HPA BB Feeder)
- M3x12 mm- x2 (HPA BB Feeder)
- M3x20 mm- x6
- M3x25 mm- x4
- M4x30 mm- x1
- M4x35 mm– x1
- M4x37 mm– x3 (not standard length, you will need to cut longer ones like i did)
- M4x41 mm– x2 (for stock, not standard length, you will need to cut longer ones like i did).
- M4x40 mm– x2
- M4x43 mm– x1 (front guard, not standard length, you will need to cut longer ones like i did)
DIN 934 - Hexagon Nuts
-M4 - x10
- M3 - x29
For TDC MOD
DIN 913 - Hexagon socket set screws with flat point
- M4x4 mm x 1
For TDC Mod wheel regulation you need a standard BIT H2 (25 mm in total length) for M4 socket screw, used in screw drivers, to insert into
3D printing settings
PRINT SETTINGS USED and print Info (I use Prusa Slicer) ,KIT was Printed on Prusa MK3S
RECOMMENDED PRINT MATERIAL ESUN PLA+ (plain PLA can be to stiff and brittle, do not print with PETG definitely to brittle, some parts will break, already tested)
ADHESION I use BuildTak pads on steel spring sheets, so be sure that your adhesion is excellent, if some parts warped from bed, means that adhesion was not good enough.
do not use textured bed plates only smooth ones
- Print slowly, printing quickly has a negative impact on the adhesion of the layers
- nozzle diameter 0,4 mm
- Layer Height 0.16 mm
- bottom and upper layers x 16
- Recommended Perimeters x 8
- Infill 20% to 30% is good enough thanks to many perimeters, but you can go wit 100% infill with 02 BBU BLOCKER A and 02 CHARGING HANDLE
- Cooling: use auto cooling with min 60% and 100% max for overhangs and very short layers, for better layer adhesion
- Supports YES (but not auto, use brush and smart fill in PrusaSlicer) more in manual
TOP contact distance for supports 0.16 for better removal with 2 Interface loops
BOTTOM contact distance for supports 0.2 for better stability with 2 interface layers
Support Separation from object 75%
On request If needed i can provide my settings for Prusa Slicer ( for use with Prusa MK3S printers)
- Brim: yes but i use only one pass, more for cleaning nozzle.
- Some parts REQUIRE Use of Ironing for all top surfaces, more details in manual.
In some places after print sanding is required. More in the manual.