Filament Vacuum Bag Dyson Adaptor V2 by charlie.waterworth

charlie.waterworth

3D Printer>3D Printer Accessories

GIF

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

1.8 h

1 plate

4.7(38)

PLA, 0.2mm layer, 2 walls, 15% infill

1.4 h

1 plate

4.9(9)

Minimal Support, Fast Print 0.2mm layer, 2 walls, 15% infill

45 min

1 plate

5.0(7)

PETG 0.2mm layer, 2 walls, 15% infill

1.3 h

1 plate

4.0(1)

Boost

125

267

404

258

Released

Description

UPDATED VERSION: See below for changes

This little Dyson attachment can be inserted in to the seal of a filament vacuum dry bag and suction all the air out in a second or two!

This is a way better option than the little hand pump that comes with the popular AliExpress/Temu/Amazon filament vacuum bags.

This is an updated version of the original model ( https://makerworld.com/en/models/165870#profileId-182127 ) with improvements based on user feedback:

Oval nozzle to make it easier to seal the bag when removing the nozzle
There is a pressure release vent to allow the Dyson to run at full power without triggering the “blocked” pulsing mode on the Dyson
The inside profile has been reworked to remove overhangs and reduces the amount of support needed when printing (still recommend support enable for the button and side flange overhangs)

Designed for my V8 and believe it fits all V models from V7 onwards? (V6 and older had a different connector design). Let me know in the comments which models it fits.

Comment & Rating (63)

@Chad

Print Profile

0.2mm layer, 2 walls, 15% infill

nice solution. Was extremely tight on both Dysons, v8 and v7. To the point that they would not insert more than a 1/4 inch. I measured the print file and the actual print. The print is spot on to the dimensions of the file. I needed to thin the wings down significantly to allow it to seat entirely. The body was perfectly sized.

The designer has replied

@charlie.waterwo

There have been a couple of comments like yours saying it's a tight fit, but I haven't come across this myself in PLA or PETG on any Dyson. I've tested on brand new models in store too. I think it may be due to filament/setting variables, maybe some layer ouze etc. I may update the model with a little more tolerances.

@Chad

Replying to @charlie.waterwo :

I printed it on an A1 using Jayo PLA+ if that helps at all. Thanks for the response!

@thowell169

Print Profile

Minimal Support, Fast Print 0.2mm layer, 2 walls, 15% infill

Came out great, Thanks for sharing.

@metus88

Print Profile

Minimal Support, Fast Print 0.2mm layer, 2 walls, 15% infill

it's ok. No problem

@btizl

Print Profile

PLA, 0.2mm layer, 2 walls, 15% infill

Nice print, but it is not compatible with my vacuum.

(Edited)

@D2Designs

Print Profile

0.2mm layer, 2 walls, 15% infill

Perfect, just what I was looking for

@Picchietto

Print Profile

Minimal Support, Fast Print 0.2mm layer, 2 walls, 15% infill

it perfectly fit, maybe a bit too tight but definitely better than too loose

@ldean807

Print Profile

0.2mm layer, 2 walls, 15% infill

very nicely done, was hoping it would fit a standard vacuum hose or a mattress pump fitting. but this printed really great quality.

@Shooka

Print Profile

0.2mm layer, 2 walls, 15% infill

Simple et efficace

@user_2146525820

Print Profile

0.2mm layer, 2 walls, 15% infill

The print quality was outstanding.

@kwindolph

Print Profile

0.2mm layer, 2 walls, 15% infill

in Ordnung. Geht leider etwas schwer in den V15 rein. Muss etwas geschliffen werden.

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.