Avocado germinator

Copyright Claim

Avocado germinator

Boost
265
385
45

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

Perfect 0.2mm layer, 3 walls, 15% infill
Perfect 0.2mm layer, 3 walls, 15% infill
Designer
1 h
1 plate
4.8(32)

0.2mm layer, 2 walls, 10% infill
0.2mm layer, 2 walls, 10% infill
1 h
1 plate
4.5(10)

A1 mini, 0.2mm layer, 3 walls, 15% infill
A1 mini, 0.2mm layer, 3 walls, 15% infill
1.1 h
1 plate
5.0(2)

Boost
265
385
45
1
382
256
Released

Description

Do you want to plant an avocado? This support will be very useful for planting it.

 

Follow the instructions for planting.

  1. Keep the bone clean. When you eat this superfood, be careful not to cut it. Wash it to remove any meat remains that may be attached to it.
  2. Identify its parts. Although the bone appears spherical, it is key to know which is the upper part, —since the sprout will grow from it—, and which is the lower part, from which the root will sprout. The slightly pointed area is the upper one.
  3. Put the bone inside the sprouting support and place it inside a glass.
  4. Add water until it covers half of the avocado pit.
  5. Put the glass in a place with direct sun and avoid cold spaces. Change the water every two days to keep it clean and fresh. The roots and stem should begin to sprout in two to six weeks. If nothing happens in a month or so, throw it away and try a new seed.
  6. When the stem is about 15 cm (3-4 weeks old), cut it in half and leave it approx. in 7 cm (even if it hurts, but it is about stimulating the roots).
  7. When the roots are thicker and the stem has leaves again, plant the seed in a pot. Leave it sticking out of the ground as it was in the glass. Place the pot in bright, indirect light. Water carefully. The soil must remain moist, but not soggy.
  8. You'll know you're overwatering if the leaves start to turn yellow and droop. If this happens, stop watering and allow the soil to dry out before watering again.

Comment & Rating (45)

Please fill in your opinion
(0/5000)

Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
fits perfect!
1
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
already in use
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
Thank you for sharing art ⚡️
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
thanks for very nice design.
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
great profile. printed great
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
Wife is amazed, so I’m grateful my fella! printed with Fillamentum Traffic Black and tree supports.
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
MOLTO BELLO!
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
top
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
Nice Idea. Top Print. Thanks…🥰
0
Reply
Print Profile
Perfect 0.2mm layer, 3 walls, 15% infill
This popped up in my daily browse, perfect timing as I had a seed sitting on the kitchen counter ready to go :) Printed out in PETG perfectly. Thanks for the added information which is often forgotten.
(Edited)
0
Reply