Skip to content

WW2 Russia Mosin-Nagant M28/30 (Finnish) RIFLES 1:35/1:72

🔫 3D models of guns or weapons are dummy objects or prop toys and have no real functionality as weapons. They are intended for entertainment or decorative purposes only. For any design violating our T&Cs, please report them.

Advertising
Advertising
?
Creation quality: 0.0/5 (0 votes)
Evaluation of members on the printability, utility, level of detail, etc.

  • 269 views
  • 1 download
  • 1 collection

License
3D design format
STL Folder details Close
  • 1-35_mosin_m28.stl
  • 1-72_mosin_m28.stl

Learn more about the formats

Publication date 2024-03-26 at 08:20
Design number 1881063

3D printer file info

3D model description

The Mosin–Nagant is a five-shot, bolt-action, internal magazine–fed military rifle. Known officially as the 3-line rifle M1891[9] and informally in Russia and the former Soviet Union as Mosin's rifle (Russian: винтовка Мосина, ISO 9: vintovka Mosina), it is primarily found chambered for its original 7.62×54mmR cartridge.

Developed from 1882 to 1891, it was used by the armed forces of the Russian Empire, the Soviet Union and various other states. It is one of the most mass-produced military bolt-action rifles in history, with over 37 million units produced since 1891. In spite of its age, it has been used in various conflicts around the world up to the present day.

Most Finnish Rifles were assembled by SAKO, Tikkakoski Oy, or VKT (Valtion Kivääritehdas, State Rifle Factory, after the wars part of Valtion Metallitehtaat (Valmet), State Metalworks). The Finnish cartridge 7.62×53mmR is a slightly modified variation of the Russian 7.62×54mmR, and is considered interchangeable with 54R. However, the older version of the Finnish military cartridge was loaded with the S-type bullet that had nominal diameter of .308. In 1936 the Finnish Army fielded a new standard service cartridge intended for both machine guns and rifles. This new cartridge was loaded with a new bullet designed in 1934–the D-166, which had a nominal diameter of .310. The new service rifle m/39 was designed from the start around the D-166 thus it had nominal barrel diameter of .310.

Handloaded cartridges for Finnish rifles should however use a 0.308 inches (7.8 mm) bullet for use with other Finnish Mosin–Nagant variants instead of the 0.310 inches (7.9 mm) one which gives best results in M/39, Soviet and most of other Mosin–Nagant rifles.

M/28–30: An upgraded version of the M/28. The most noticeable modification is the new rear sight design. The same sight was used in following M/39 rifle only exception being "1.5" marking for closest range to clarify it for users. According to micrometer measurements and comparison to modern Lapua D46/47 bullet radar trajectory data, markings are matched to Finnish Lapua D46/D46 bullet surprisingly accurately through whole adjustment range between 150 m and 2000 m.
The trigger was also improved by adding coil spring to minimize very long pre-travel. Following M/39 does not have this improvement. The magazine was also modified to prevent jamming. Magazines were stamped with "HV" (häiriövapaa = Jam Free) letters in right side of rifle. Later M/39 uses identical design, but without "HV" -stamp. M/28–30 also have metal sleeve in fore-end of handguard, to reduce barrel harmonics change and to make barrel-stock contact more constant between shots and/or during environmental changes such as moisture and temperature. Later M/39 does not have this upgrade.
In addition to its military usage, approximately 440 M/28–30 rifles were manufactured by SAKO for use in the 1937 World Shooting Championships in Helsinki.
M/28–30 model, serial number 60974, was also used by Simo Häyhä, a well-known Finnish sniper. M/28–30 was used as Civil Guards competition rifle before World War II, as was the case with Simo Häyhä's personal rifle. Therefore, rifles were built very well, with highest grade barrels available and carefully matched headspace. Häyhä's rifle was still at PKarPr (Northern Karelia Brigade) museum in 2002, then moved to an unknown place by the Finnish Army.[41]

I have set them to a 1:35/1:72 ratio for easy printing, and the size comes from the data provided by the encyclopedia. You can adjust its size to any place by yourself.

Note: If using the model for 3D printing, model repairs may be needed.

Advertising


Issue with this design? Report a problem.

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi 💜.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!


Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.

100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.