NOTICE: REMIX ARE NOT ALLOWED

NOTICE: DO NOT POST ANY OF YOUR PROFILE

I remixed my model “PURGE CHUTE COVER WITH SILICON NOZZLE WIPER” , link: 
https://makerworld.com/en/models/145761#profileId-158636 The last version was only in one color and the logo was engraved.

Benefits:

• Suitable for ABS. BUT I STILL RECOMMEND HIGHER TEMPERATURE FILAMENT , LIKE PA6-GF/CF , PATH-CF OR PC
• NO WARPING USING ABS WITH BED TEMPERATURE AT 97°C
• Tighter fit
• Bambu Lab logo not engraved, 0.01 offset
• Multicolor : white , black and green
• Purged filament doesn't jump on the plate
• Nozzle is better cleaned
• Pieces of purged filament don't go everywhere , each corner of the printer remains clean

Example of the black version:

How to install THE MODELS WITH and WITHOUT THE LOGO:

How it works:

INSTRUCTIONS

What is the nozzle wiper made of?

It is made from a piece of silicone from the molds used to make pancakes. Like this one you see in this pic:

How big should the silicone piece to be cut be?

10mm x 2mm x 15mm

PRINT THE POOP STOP WITH THE NOZZLE WIPER

CUT THE PIECE:

APPLY THE SILICON PIECE IN THE SEAT OF THE POOP STOP AND INSTALL THE POOP STOP IN THE POOP BUCKET

AS YOU SEE IN THIS PIC , MY MODEL IS SUPER FLAT, SO WARPING MUSTN'T BE ON IT TO AVOID CRASHED OR SCRATCHES AGAINST THE HOTEND, TOOLHEAD OR FAN DUCT , SET THE BED TEMPERATURE AT 97°C :

I have tested this model so many times and it works smoothly! No issue.

ALL THE MODELS ARE AVAILABLE ON MY PAGE.

NOTICE:

DON'T MODIFY THE ORIENTATION!

NOTICE: THE FOLLOWING PHOTO SHOWS THE EXTRUDED FILAMENT BEING HELD ON THE SILICON NOZZLE WIPER, BEFORE PRINTING.

THIS IS ONE OF THE MAIN REASONS WHY I DESIGNED THIS MODEL. THAT EXTRUDED FILAMENT COULD RUIN YOU FIRST LAYER!

PLEASE CHECK ALWAYS IF THE SILICON NOZZLE WIPER IS CLEAN AND IF YOU SEE THAT SOME EXTRUDED FILAMENT HAS BEEN DEPOSITED ON IT, REMOVE THE EXTRUDED FILAMENT AND ENJOY 3D PRINTING.

THE PHOTO WAS MADE AS EXAMPLE AFTER 3h PRINTING.

MY MODEL HAS ALREADY BEEN TESTED, FOR A MONTH AND I DON'T FIND ANY PROBLEMS.

𝙽𝙾𝚃𝙸𝙲𝙴:

𝚃𝙷𝙸𝚂 𝙸𝚂 𝙰 𝚂𝙸𝙼𝙿𝙻𝙴 𝙿𝚁𝙸𝙽𝚃. 𝙰𝚂 𝚈𝙾𝚄 𝚂𝙴𝙴 𝙸𝙽 𝚃𝙷𝙴 𝙿𝙸𝙲𝚃𝚄𝚁𝙴𝚂 , 𝙼𝚈 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺 𝚅𝙴𝚁𝚈 𝙶𝙾𝙾𝙳 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳. 𝚂𝙾 𝙱𝙴𝙵𝙾𝚁𝙴 𝚈𝙾𝚄 𝙶𝙸𝚅𝙴 𝙱𝙰𝙳 𝚁𝙰𝚃𝙸𝙽𝙶 𝚃𝙾 𝙼𝚈 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂, 𝙱𝙴 𝚂𝚄𝚁𝙴 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽 𝙰𝙽𝙳 𝙰𝚂𝙺 𝚃𝙾 𝚈𝙾𝚄𝚁𝚂𝙴𝙻𝙵 , 𝚆𝙷𝚈 𝚈𝙾𝚄 𝙳𝙾𝙽'𝚃 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽. 𝙸 𝙳𝙾𝙽'𝚃 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚄𝙿𝙻𝙾𝙰𝙳 𝙰 𝙻𝙾𝚃 𝙾𝙵 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂 𝙵𝙾𝚁 𝙴𝙰𝙲𝙷 𝚂𝙸𝙽𝙶𝙻𝙴 𝙿𝚁𝙾𝙱𝙻𝙴𝙼 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰𝙽𝙳 𝙵𝙾𝚁 𝙴𝚅𝙴𝚁𝚈 𝚂𝙸𝙽𝙶𝙻𝙴 𝙼𝙾𝙳𝙴𝙻! 𝙴𝚅𝙴𝙽 𝚈𝙾𝚄 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚂𝙷𝙰𝚁𝙴 𝙾𝙽𝙴 , 𝙸𝚃 𝙳𝙾𝙴𝚂𝙽'𝚃 𝙼𝙰𝙺𝙴 𝚂𝙴𝙽𝚂𝙴 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚂𝙸𝙼𝙿𝙻𝙴 𝙼𝙾𝙳𝙴𝙻 𝙸𝚃𝚂𝙴𝙻𝙵!

𝙿𝙻𝙴𝙰𝚂𝙴, 𝙻𝙸𝙺𝙴 𝙸 𝚂𝙰𝙸𝙳 𝚃𝙷𝙴 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺𝚂 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳 𝙴𝙰𝚂𝚈! 𝙽𝙾𝚃 𝙰𝙻𝚆𝙰𝚈𝚂 𝚁𝙴𝙳𝚄𝙲𝙸𝙽𝙶 𝚃𝙷𝙴 𝚂𝙿𝙴𝙴𝙳 𝙲𝙰𝙽 𝙷𝙴𝙻𝙿 𝚈𝙾𝚄 𝚃𝙾 𝚂𝚃𝙸𝙲𝙺 𝙴𝚅𝙴𝚁𝚈 𝙼𝙾𝙳𝙴𝙻 𝙾𝙽 𝚃𝙷𝙴 𝙿𝙻𝙰𝚃𝙴! 𝚃𝙷𝙰𝙽𝙺 𝚈𝙾𝚄 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚄𝙽𝙳𝙴𝚁𝚂𝚃𝙰𝙽𝙳𝙸𝙽𝙶!

ᴵᶠ ʸᵒᵘ ʰᵃᵛᵉ ᵖʳᵒᵇˡᵉᵐˢ ᵃᵇᵒᵘᵗ ᵗʰᶦˢ ᵐᵒᵈᵉˡ, ʲᵘˢᵗ ˢᵉⁿᵈ ᵐᵉ ᵃ ᵖʳᶦᵛᵃᵗᵉ ᵐᵉˢˢᵃᵍᵉ ᵃⁿᵈ ᴵ'ˡˡ ʰᵉˡᵖ ʸᵒᵘ.

ᴳᶦᵛᵉ ᵐᵉ ᵃ ˡᶦᵏᵉ ᵃⁿᵈ ᶠᵒˡˡᵒʷ ᵐʸ ᵖᵃᵍᵉ.

ᵀʰᵃⁿᵏ ʸᵒᵘ ᵗᵒ ˢᵘᵖᵖᵒʳᵗ ᵐᵉ ᵃⁿᵈ ʰᵃᵖᵖʸ ᵖʳᶦⁿᵗᶦⁿᵍ.