Minecraft-inspired Christmas House by chiz_m

chiz_m

Household>Festivities

GIF

Print Profile(8)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

house 1 - 0.2mm layer, 2 walls, 15% infill

Designer

20 h

13 plates

4.8(4)

santa hat (2-part print) 0.2mm layer, 2 walls, 15% infill

Designer

39 min

2 plates

5.0(3)

candy cane - 0.2mm layer, 2 walls, 15% infill

Designer

1.1 h

3 plates

4.7(3)

santa hat - 0.2mm layer, 2 walls, 15% infill

Designer

1.6 h

1 plate

4.7(3)

Click to see more

Boost

130

215

326

410

Released

Description

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!

REVISION HISTORY

2023-12-09: Added the star to the Xmas Tree profile. Thanks to todd for catching it!

2023-12-03: Added platform print profile and assembly steps to the guide.

2023-11-28: Added house print profile and house assembly to the guide.

2023-11-27: Added Santa hat and pine tree print profiles. Updated Assembly Guide to include Christmas tree assembly.

2023-11-26: Early access - Draft assembly guide released. You can start downloading and printing so you'll be ready with all the parts once the final assembly guide is released.

DESCRIPTION

This is an expansion of my Minecraft-inspired Base/Diorama Builder containing all-new blocks with new textures! Utilizing these new blocks is a Christmas house complete with a large Christmas tree and other elements for a scenic Minecraft Christmas house display!

ASSEMBLY GUIDE

Available for download is an assembly guide showing the step-by-step assembly steps for the house, xmas tree, pine tree and candy cane.

SANTA HAT

Two sizes of the Santa hat are available: 1) small one that compatible with most of the mini-figure mobs that has the same size head as Steve's and 2) large size that will fit the Creeper and Enderman heads. You can download the mini-figures here: mini-figures

LIGHTING

To add lights into the model, I used these fairy lights available at Amazon. The blocks are hollow and it's easy to route the lights inside. However, you may need to drill some holes or make holes a little bigger on parts that come with holes using a pin vise.

Documentation (1)

Assembly Guide (1)

Minecraft-inspired Christmas House - Assembly Guide.pdf

Comment & Rating (37)

@peter.st

este 2 dni tlacenia :) a synátor moze skladať.

The designer has replied

@chiz_m

😮 Wow! Veľmi organizované! Tešíme sa na hotový výtlačok!

@danielsaid

Print Profile

santa hat (2-part print) 0.2mm layer, 2 walls, 15% infill

I tuned my filament before printing, using the retraction method to save 20mm purge plus calibration. printed perfect without brims. excited to make a million more

@mxmark4

so cool!!!

The designer has replied

@chiz_m

Thank you!

@mxmark4

I am making the lanterns right now and the house is cool!

@mxmark4

after that I will make Santa hats but can you make the hats two different parts so I can do multiple colors? ( I don’t have ams)

@dolejsi.jr

Its nice

@atknyanik

I cannot remove the blocks after installing them. Too tight. My printer is Bambu Lab X1 Carbon Combo. My filament is eSUN PLA+. Even though I reduced the flow rate by 0.01 it is still tight. What temperature do you recommend? Is there anything else I should do?

The designer has replied

@chiz_m

Try reducing your flow rate by another 0.01 until 0.97. I have filaments where I had to go that low. If it's still too tight, try reducing temperature by 5°. You will know that you gone too low if you start to see under extrusion. Also, as you test, print two (2) blocks at at time before printing lots of blocks. Also, you may need to this calibration on each filament color you'll be using even same brands.

@Luckyboi

great models and insanely well produced might print this when i get the chance

(Edited)

The designer has replied

@chiz_m

Thanks for the feedback!

@peter.st

Print Profile

house 1 - 0.2mm layer, 2 walls, 15% infill

este tlacim diely, vyzera to dobre, pasuje zatial do seba vsetko,.

The designer has replied

@chiz_m

Dobré počuť! Ďakujeme za hodnotenie a spätnú väzbu! Dúfam, že keď budeš hotový, môžeš pridať fotky :)

(Edited)

@espariz

Wow! Great designs! Thanks! Do you recommend on Bambu A1 mini to configure some XY contour compensation of -0.02 or something? Or better at zero? Thanks!!

The designer has replied

@chiz_m

Hi! Thanks for the feedback! I suggest print with a baseline, i.e., using default printing and filament profile. Then if you find the fit too tight, play on the filament profile by reducing flow rate by 0.01 until you have just the right fit. You may need to do this for every filament coz each filament may not have the same printing properties. Good luck printing and enjoy!

@SolarTim

Print Profile

xmas tree, 0.2mm layer, 2 walls, 15% infill

Very cool

(Edited)

@iceman011235

Print Profile

santa hat - 0.2mm layer, 2 walls, 15% infill

The designer has replied

@chiz_m

Thank you so much for taking the time to rate my profiles!

(Edited)

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.