Bambu A1 Wyze Cam V1/V2 Mount (No hardware) by JohnPepsi

JohnPepsi

3D Printer>3D Printer Accessories

GIF

Print Profile(1)

All

Tree Supports

Designer

1.3 h

1 plate

4.6(11)

Boost

120

149

Released

Description

Not happy with the camera on your A1 or A1 Mini? Got a spare Wyze Cam V1 or V2 laying around? Give this print a try! This is very simple design that uses very little filament and can be printed in very little time, this adds an actual live video feed to to your A1/A1 Mini as well as the bonus of night vision. This design uses no hardware and simply presses into place still allowing the factory camera and light to function.

Camera can be easily removed for access to the optional micro SD card (needed for recording and time-lapse)

Print with whatever setting you prefer just make sure to turn on supports! (very little needed)

Best orientation is the flat side with the circles down

12/21/20223 **STL has been updated to reflect better stability (BambuA1_WyzeCamV1/V2_Mount.stl)

WyzeCam v3 added- (https://makerworld.com/en/models/102933#profileId-109617)

Wyze Cam OG Now Available https://makerworld.com/en/models/150898#profileId-164636

Version 2 now posted https://makerworld.com/en/models/150985#profileId-164698

Comment & Rating (30)

@WagZPrintZ

Will this work on the mini also!?

The designer has replied

@JohnPepsi

I'm working on a mini version right now. I thought it would but I guess they're different

@WagZPrintZ

Replying to @JohnPepsi :

I found your mini variant. I’m printing it now to see what’s up.

@JohnPepsi

Replying to @WagZPrintZ :

Let me know

@sunderdick82

Print Profile

Tree Supports

Does not Fit A1 Mini. Had to break off outer top tab and trip out the notch.

The designer has replied

@JohnPepsi

sure you printed the correct profile? there are two profiles, one for the A1 and one for the A1 Mini. if the cord was too tight, you most likely printed the one for the A1

@user_4259807396

Replying to @JohnPepsi :

I didn't find the configuration file for A1 Mini. Did you upload it correctly?

@JohnPepsi

Replying to @user_4259807396 :

My apologies, I believe the A1 Mini is just a raw STL in that file. but if you go to my uploads, the version two of the mount has a A1 mini profile

@MusicCity3D

I printed this but mine doesn't seen to stay on the A1. When i start a print from my computer and then go to where my printers are in my house, the mount is always laying on the table. Somehow it gets knocked off or vibrated off when the prints starts because I slide it back on and it stays on throughout the whole print.

The designer has replied

@JohnPepsi

Make sure when you're putting it on. it's not going above the rubber around the power cord, and needs to go around the rubber. that's kind of what it uses to hold snug in place

@MusicCity3D

right and it is but it just pops up back over the rubber piece.

@jcbohman

just wanted to let you know the Wyze Cam OG unfortunately didn’t work with this model, so I modeled one up last night. Here is a link if you’re interested. thanks again. https://makerworld.com/models/103953

(Edited)

The designer has replied

@JohnPepsi

yeah I didn't know there was an OG camera. unfortunately I don't have one to do a revision, yours looks good though

@dwillinsky

what filament did you use? it is an exact match!

The designer has replied

@JohnPepsi

https://www.amazon.com/dp/B0BXSMVBFM?ref=ppx_yo2ov_dt_b_product_details&th=1 its a pretty close match