BambuLab AMS Lite Tower Caps by funhun7erz

funhun7erz

3D Printer>3D Printer Accessories

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.16mm layer, 2 walls, 15% infill

Designer

3.4 h

1 plate

4.8(8)

0.16mm layer, 2 walls, 15% infill

Designer

27 min

1 plate

4.8(6)

0.16mm layer, 2 walls, 15% infill

Designer

26 min

1 plate

Boost

Released

Description

Were you in a situation that you watch your sweet little A1 mini and admireing it for hours? Bzzzz brrr bzzzz. And then while still hypnotized you get to the top part of the AMS lite and you see those "towers". Urgh... Uglyyyyy!
Left by the creators Bambu Lab just to test how long would it take until you print your own "tower rings" and level up your "posh" skill.

This is a must have mod for your Bambu Lab A1 mini Combo and is recommended by people all over the world! At least two!!
Join them and enjoy the new look of your AMS lite. Stop being ashamed to show your AMS lite! Be proud owner with the new "AMS lite tower caps" by FH7z!

Why not printing them in different colors and even change them every day!?! It can fit your outfit, the weather or EVEN your wife's mood!

You can choose from models that include:
- Ring for the "towers" that sits on top to make it look nicer
- Ring for the "towers" with 3 "BUDs" inside that mimic the shell of the AMS. For those who wants finished look and appreciate details.

The model took ashamingly long time and tens of test prints as Bambu decided to make strange design with strange dimensions. The idea was to make them fit perfectly as a shape and be practical - snug but at the same time loose enough so they would be able to be removed (without a hammer).
The design is optimized for Bambu filament and tested with more than 6 colors which all returns same precise result. Profiles used in tests were the standard A1 ones for 0.16 and 0.20 layer height and both worked just fine.

If you like this model, please post your creations and thoughts.
Please share the model if you like it.
Fell free to remix and share your creations with us.

!Note: The rings with buds has only one way of fitting so measure before trying to fit.

Check out our "AMS lite accessories kit" for decorating your AMS mini even further =))

Comment & Rating (27)

@RoHeryn

Print Profile

0.16mm layer, 2 walls, 15% infill

It’s perfect ! This printer is also for my 10 and 7 yo boys, so I think it will help them. and it’s pretty ☺️

The designer has replied

@funhun7erz

Woow, thanks for printing this. Hope your boys likes it :) For kids you can check my other designs where I have designed a cap that can hold up an accessory =))

@gnuaha7

Great idea! I print one for each new filament.

The designer has replied

@funhun7erz

Thanks for printing. I was thinking the same the other day but then I decided I am too lazy to change them all the time each day :D How would you rate getting them off/on again?

@user_3305200239

Great project. The rings fits perfectly to my printer. Thank you!

@MarkyMarky

Print Profile

0.16mm layer, 2 walls, 15% infill

Great Idea breaks up the Grey on the AMS feeders! Nice snug fit. Used PETG

(Edited)

@mfenninger056

Great job.

The designer has replied

@funhun7erz

Thank you. Did you like them?

@mfenninger056

yes they worked out great.

@snkxn75dvs

Print Profile

0.16mm layer, 2 walls, 15% infill

good print, nice fit

The designer has replied

@funhun7erz

Thank you for printing and feedback

@MalcTheOracle

Print Profile

0.16mm layer, 2 walls, 15% infill

I originally tried printing one per filament in the wild idea that I would swap them out to match the filament each time I swapped that. I quickly bored of doing that. Doesn’t stop this being a decent design and does have its benefits.

(Edited)

The designer has replied

@funhun7erz

LoooL same thing with me. Thought I printed a few up and change them from time to time. You can check my other designs where I have designed a cap that can hold up an accessory =))