Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )
Copyright Claim
Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )
Boost
44
86
24
Print Profile(4)
Lid Handle - Bottom on Buildplate
Designer
22 min
1 plate
Lit Handle - Top on Buildplate
Designer
21 min
1 plate
0.2mm layer, added Brim
23 min
1 plate
0.08mm layer, 2 walls, 15% infill
54 min
1 plate
Boost
44
86
24
2
142
131
Released
Description
Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )
This is a replacement for the original Handle on the Glass Hood for the P1 and X1 Series. It integrates a stand that you can flip over, to allow additional airflow without removing the Glass Hood. The hinge is printed in place and the surface area is left blank intentionally, it´s easy for you to add a logo on top, and I don't get legal issues 😜.
Installation
Just unscrew the original handle, and reuse the screws to install the replacement. Done.
I hope you enjoy the design, please leave a comment/rating if you enjoy it or share your feedback!
Comment & Rating (24)
All
Print Profile
Lid Handle - Bottom on Buildplate
Nice looking Tool. Prints well, but i had to use a Brim.
Thanks for Sharing 👍🏻
The designer has replied
1
Reply
Clean plate worked for me 😅
0
Reply
Replying to @benjaminkott
I tried to clean the bed twice, unfortunately without success :D. The bottom wall is unfortunately very narrow, maybe you could make it a bit wider. Otherwise very nice model
0
Reply
Replying to @Mr.Haix
i thought about it during designing but it made the model to clunky for my taste. If the brim helps some it's a tradeoff I would take in this case.
(Edited)1
Reply
5 STAR! Love this little easy gadget and added the logo for being extra. Thank you so much!
1
Reply
Print Profile
Lid Handle - Bottom on Buildplate
worked as expected.
(Edited)
1
Reply
Print Profile
Lid Handle - Bottom on Buildplate
The best looking Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )
1
Reply
Print Profile
Lid Handle - Bottom on Buildplate
1
Reply
Print Profile
Lid Handle - Bottom on Buildplate
Really sleek print to both close or lift the top panel when printing Pla to vent the heat. Recommended if your Ams is not on top of the printer
1
Reply
My ABS one works (for now) even with AMS on the glass. Eats into a rubber seal a little to much for my liking though.
EDIT: DO NOT USE WITH AMS ON THE GLASS. Leg holds fine but that much weight on one point on printer frame is probably not safe. Part of my plastic frame is now bent.
Can't speak of use with a risers though or led frames. As I didn't use one.
(Edited)0
Reply
Replying to @Gamp
Ya seems like there is only a small area for it to rest on the rubber gasket at the top.
0
Reply
Print Profile
Lid Handle - Bottom on Buildplate
Works as expected
1
Reply
Boosted
Print Profile
0.08mm layer, 2 walls, 15% infill
Printed in Polylite PLA PRO.
1
Reply
Print Profile
Lit Handle - Top on Buildplate
I had a bed adhesion issue and ended up going with a different model
Bed Adhesion Issue:The smaller piece came detached within the first few layers
The designer has replied
0
Reply
@jrodbrown58 sorry to hear that. But sadly cannot verify here it. Everything seems to work fine. https://youtu.be/7g6hqUOR5UE
0
Reply
Print Profile
0.2mm layer, added Brim
Easy to work with, and does what I needed
1
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld