Kitchen Sink Organizer

Kitchen Sink Organizer

Boost
134
253
30

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
12 h
4 plates
4.7(10)

SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
Designer
10.5 h
3 plates
4.7(9)

Boost
134
253
30
2
277
264
Released

Description

Dishware storage solution.

 

Two different sizes. 264 x 132 x 173 mm, 10.4 x 5.2 x 6.8 inches and 220 x 110 x 145 mm, 8.6 x 4.3 x 5.7 inches (80% model).

 

Also see a slightly smaller Cutlery Stand model with a similar design.

 

I wanted to make this item strong so it would last well for a long time. There is space between the parts, so you can reduce the size of the model. The model consists of four parts and you can add another dividing wall if you like.

 

The idea was to calm the environment around the kitchen sink area to make it look more homely. Dish washing detergent, dish brush, sponge, etc. can be hidden well to this solution and are easy to take out when needed.

 

The water that drains from the accessories collects in the container below and evaporates in time, or it can be emptied easily, because the main container has a perforated bottom, so it can be lifted out to empty the water container.

 

The design idea was to find a calm design language suitable for many decoration styles. I hope that this will find its way into many people's homes and make everyday life easier and more cozy. Thank you!

 

 

Comment & Rating (30)

Please fill in your opinion
(0/5000)

Print Profile
SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
very beautiful print, main compartment and tray printed perfectly with no issues. I had issues with the printing of the divider, it knocked itself over multiple times due to the very thin upright print. the basket had issues with the support material. the edges have a significant overhang which once it started printing it warped and didn’t seem to adhere properly to the supports. tried to glue it mid print but didn’t really work. still great but some tricky elements
The designer has replied
1
Reply
Thanks for the pictures and feedback! Sorry to hear that the printing was not completely successful. If you have challenges printing the Sponge holder. I recommend that you try to lower the temperature, for example, from 220 degrees to 210 degrees. You can also choose Silent Mode to slow down the print speed. Hope these help you get a better result! 😊
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
Ausgezeichnet 👏👏👍
The designer has replied
1
Reply
Nice! 😊👍🏻
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
I'm really happy with how it turned out
The designer has replied
1
Reply
Thanks for sharing the picture! 😊 Looks really well done and suitable sizing.
(Edited)
1
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
Very nice model, thanks!
0
Reply
Print Profile
SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
The designer has replied
1
Reply
Thanks for sharing the picture! Really nice filament! Looks great!!
0
Reply
Print Profile
SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
(Edited)
The designer has replied
1
Reply
Nice! Thanks for sharing the picture!
0
Reply
very nice!!!!
The designer has replied
1
Reply
Thanks! 😊
0
Reply
Print Profile
SmallerOne (80%model) 0.2mm layer, 4 walls, 15% infill
brilliant print,well worth the time and effort,quality
The designer has replied
1
Reply
Thank you! 😊
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
great print
The designer has replied
1
Reply
Thank you! 😊
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
Prints and looks great!
1
Reply