Flexi Baby dragon.v2.0 update new stronger wings multi color
Copyright Claim
Flexi Baby dragon.v2.0 update new stronger wings multi color
Boost
403
652
95
Print Profile(2)
0.2mm layer, 2 walls, 10% infill. stronger wings
Designer
12.9 h
2 plates
Single Color Dragon
1.8 h
1 plate
Boost
403
652
95
1
1.3 k
753
Released
Description
Introducing the latest update of my Flexi Baby Dragon ! ✨ In this enhanced version, I've added extra functionality compared to the previous one. This little dragon can move more, has more details, and its hindquarters have been shortened, allowing you to perch on it. Excitingly, it now also features movable wings for an even more dynamic experience!
Take a closer look, and you'll discover that the arms, legs, and wings can move individually, adding an extra level of realism. I've also made it slightly smaller, but you can adjust the size—just be cautious not to make it too small, so the movement remains smooth.
So here's this upgraded dragon, ready to impress with play, where more details make a big difference! 🌟🔧
Comment & Rating (95)
All
Print Profile
0.2mm layer, 2 walls, 10% infill
ist super geworden, aber sinnvoll ist es den auf einer Platte mehrfach zu drucken, da kommt viel Müll sonst zusammen
2
Reply
Print Profile
Single Color Dragon
Sehr niedliche Baby Drachen, die Datei ist sehr groß über 1Millionen es müßte verkleinern werden
1
Reply
Print Profile
Single Color Dragon
really nice and quick print. Wings are like loose. I have to glue them. using Bambu basic PLA
1
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill. stronger wings
so nice
(Edited)
0
Reply
I managed to print the wings on the first try, but I put the printer into "Silent" speed to reduce the shaking. It might not have been needed due to the brim. On the other hand, the brim preset for the body was a pain to remove so that I could free the joints.
It is VERY flexible, more so that just about any other "flexi" print I have done. The eyes apparently were painted rather than being a separate part - I chose to omit that color. The wings snapped into the sockets OK after sanding.
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill. stronger wings
I managed to print the wings on the first try, but I put the printer into "Silent" speed to reduce the shaking. It might not have been needed due to the brim. On the other hand, the brim preset for the body was a pain to remove so that I could free the joints.
It is VERY flexible, more so that just about any other "flexi" print I have done. The eyes apparently were painted rather than being a separate part - I chose to omit that color. The wings snapped into the sockets OK after sanding.
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill. stronger wings
I tried printing 6 of these using FlashForge Burnt Titanium PLA and Overture Easy Digitial Blue PLA. The wings failed at about the same point close to the end (picture of one) so I tried a second batch with a tweaked brim and PEI textured plate temp of 65c to no avail. Failed again at the same point as they are just too top heavy to not get knocked over.
I'm pretty disappointed I could get the wings to print successfully. They are still cute though.
(Edited)Bed Adhesion Issue
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill. stronger wings
super cute, I had a small issue with the one wing but I believe the creator has fixed this in V2. I am currently printing that version. Thank you!!
0
Reply
Print Profile
Single Color Dragon
Failed print cause the wings lost adhesion in plate. I hade to re-print the separately
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill. stronger wings
cool little dragon!
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld