Am AMS-Stand with optional Buildplateholder 3x or 5x von PS11-Print fand ich die “horizontalen Löcher” zwischen den Schubladen nicht so schön, weshalb ich dafür eine eigene Lösung erstellt habe. Der Aufbau erfolgt komplett nach dem Original.
Wenn alles so weit aufgebaut ist, kommt meine kleine Ergänzung. Ein Stück Pappe von einem Filament Karton in der Breite der Schubladen ausschneiden. Die unterste Schublade einlegen, die Pappe darauf (siehe Foto). Jetzt kommen die vier gleichen Teile auf Bauplatte 5 zum Einsatz. Jeweils in die zwei ausgesparten Ecken des ersten Bauteils etwas Sekundenkleber geben und dann wie auf dem Bild ersichtlich zwischen Pappe und Schiene schieben, ggf. die Enden der Schiene runter drücken, so dass das Bauteil eine gute Verbindung mit der Schiene eingehen kann. Das Ergebnis sollte dann so sein, dass die Schiene minimal höher liegt als das eingesetzte Bauteil (siehe Bild). Nach diesem Prinzip dann einfach die restlichen Stege einsetzen. Viel Freude beim Nachbauen.
Wenn Ihnen dieses Projekt gefällt, vergessen Sie bitte nicht, zu ❤ liken und zu ★ bewerten!
At the AMS-Stand with optional Buildplateholder 3x or 5x from PS11-Print I didn't like the “horizontal holes” between the drawers, which is why I created my own solution for this. The structure is completely based on the original.
When everything is set up so far, my little addition will come. Cut a piece of cardboard from a filament cardboard the width of the drawers. Insert the bottom drawer with the cardboard on top (see photo). Now the four identical parts are used on building plate 5. Put some superglue in each of the two recessed corners of the first component and then push it between the cardboard and the rail as shown in the picture, if necessary press down the ends of the rail so that the component can form a good connection with the rail. The result should then be such that the rail is slightly higher than the component used (see picture). Using this principle, simply insert the remaining bars. Have fun replicating it.
If you like this project, please don't forget to ❤ Like and ★ Rate!
Wer nicht möchte, dass die Schubladen ganz herausgezogen werden können, kann auf deren Unterseite einen kleinen Stopper kleben. Einfach alle Schubladen bis auf die beiden obersten entnehmen. Dann das AMS-Rack auf den Kopf drehen und die Schubladen soweit herausziehen wie gewünscht. Jetzt z.B. ein Stück Korken auf die Unterseite der Schublade hinter dem vorderen Steg kleben. Anschließend kommt die mittler und zum Schluss die untere Reihe der Schubladen.
If you don't want the drawers to be pulled out completely, you can stick a small stopper on the bottom. Simply remove all drawers except the top two. Then turn the AMS-Rack upside down and pull out the drawers as far as desired. Now, for example, glue a piece of cork to the bottom of the drawer behind the front bar. Then comes the middle and finally the bottom row of drawers.
Zur Vereinfachung habe ich mein eingeständiges Modell für die Einsätze der Schubladen hier als Druckprofil aufgenommen. Vom Inlay Fix for AMS rack von xTNR21 inspiriert habe ich eine Aufteilung von 3x4 gewählt. Für die 40 mm Schubladen habe ich nun ebenfalls das Raster vorgesehen, so dass bei beiden Varianten die Einsätze draufgeklickt werden können. Hierdurch wird ein versehentliches Vermischen der Fächer unterbunden. Wer kein Raster möchte, finden entsprechende Schubladen inkl. der Einsätze unter Raw Model Files. Für jede Schubladen Größe gibt es ein eigenständiges Druckprofil.
To make things easier, I have included my stand-alone model for the Drawer Inlays here as a Print Profile. Inspired by the Inlay Fix for AMS rack from xTNR21, I chose a 3x4 layout. I have now also provided the grid for the 40 mm Drawers, so that the Inlays can be clicked on in both versions. This prevents the compartments from accidentally mixing. If you don't want a grid, you can find the corresponding Drawers including the Inlays under Raw Model Files. There is an independent Print Profile for each Drawer size.
Auf Bauplatte 5 habe ich die oberen Frontblenden (006-Front-Wall-2x) etwas vergrößert, so dass auch der Spalt über den schmalen Schubladen minimiert wird.
On building board 5 I enlarged the upper front panels (006-Front-Wall-2x) slightly so that the gap over the narrow drawers is also minimized.
Auf Bauplatte 10 habe ich die Beschriftungsschilder (012-Sign.stl) jetzt entsprechend vorbereitet. Einfach den Text und die Farben nach eigenen Wünschen ändern. Abschließend müssen die Schilder noch mit der Schrift nach unten auf die Bauplatte gelegt werden. Am einfachsten geht dies mit der Schaltfläche Automatische Orientierung. Sollten noch Fragen zu diesem Model bestehen, einfach in den Kommentaren melden. Für Hinweise, wie man die Schrift auf dem Schild automatisch zentrieren kann, wäre ich dankbar.
I have now prepared the labels (012-Sign.stl) accordingly on building plate 10. Simply change the text and colors to your liking. Finally, the signs must be placed on the building board with the writing facing down. The easiest way to do this is to use the Automatic Orientation button. If you have any questions about this model, just let us know in the comments. I would be grateful for any tips on how to automatically center the writing on the sign.
---
Forgive me for the grammar, Google helped with the translation