The Hanger - Picture Hanging Tool
The Hanger - Picture Hanging Tool
Boost
26
65
18
Print Profile(2)
Print Profile - 0.2mm layer, 2 walls, 15% infill
Designer
22 min
1 plate
0.2mm layer, 3 walls, 10% infill
32 min
1 plate
Boost
26
65
18
0
76
65
Released
Description
Let's face it, hanging pictures can be a daunting task. Getting them exactly where you want them. Nailing holes in your wall only to find it's not where it needed to be. “The Hanger” makes hanging pictures almost enjoyable!
- Attach the Hanger Tool to the frame (easily works with Sawtooth, Triangle, and D-Ring frame hangers).
- Position the frame in the desired location.
- Holding “The Hanger” firmly, remove the frame.
- Insert the nail in the hole of the triangle (where the frame was being held).
- Tap lightly on the nail to locate this position.
- Remove the Hanger Tool and nail.
- Line up the lower notch on the left edge with the nail mark from step 5.
- With "The Hanger" l vertical/plumb, use the upper notch to locate and hammer the frame nail.
That's it!
Comment & Rating (18)
All
The STL seems to be an older version. It has 2 holes on the left edge instead of slots like the .3mf has. Just a heads up!
I didn't notice until the print was complete.
The designer has replied
1
Reply
Thank you for the feedback. The 3mf file is the correct version, however, as you mentioned, the .stl file was a previous version. I have corrected the .stl file to the latest version.
1
Reply
Replying to @YelTrikDesigns
The design is great! I end up hanging lots of pictures for my work and I can't wait to bust this out next time I need to hang one. I went with petg-cf and it came out beautifully.
1
Reply
Replying to @RoyalT
This is great to hear! My wife, on the regular, is having me hang framed pictures and it's always been a nightmare! This has saved many an evening and restored marital harmony! The notched edge version is easier to use than the nail hole version. So, if you have some extra filament, I'd recommend reprinting. Happy picture hanging and thanks for the feedback. Spread the word if you have other Social Media outlets. So many struggle with this. ;-)
0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
awesome design. looking forward to hanging some frames!
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
This is one of the best picture alignment tools I've worked with. Well done!
The designer has replied
1
Reply
Comment of the day! Love hearing this feedback! I no longer fake a life threatening illness when my wife says "Let's hang some pictures!" ;-) So, thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
sehr nützlich und gut zu drucken danke an den Ersteller
The designer has replied
1
Reply
Translation: "very useful and easy to print thanks to the creator"
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
This is probably a stupid question, but why should I align the notch with the previously marked hole in step 7 and not drive the nail directly into this mark?
Maybe I'm just thinking too complicated...
The designer has replied
0
Reply
Because the top notch is aligned with where the hanger will be hung.
0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for the 5 star rating! Make sure you check out my other models and Bambu Printer Accessories. More on the way, so follow me for updates.
0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
(Edited)0
Reply
Print Profile
Print Profile - 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for the 5 star rating! Make sure you check out my other models and especially Bambu Printer Accessories. More on the way, so follow me for updates.
(Edited)0
Reply
No more
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
© 2024 MakerWorld