Divider and endcap for spool shelf by Maoirae

Maoirae

Tools>Organizers

Print Profile(6)

All

P1P

P1S

X1 Carbon

X1E

Endcap 1inch 0.2mm layer, 2 walls, 8% infill

Designer

1.7 h

1 plate

5.0(14)

Divider 1inch 0.2mm layer, 2 walls, 8% infill

Designer

1.4 h

1 plate

4.9(12)

Endcap 20mm 0.2mm layer, 2 walls, 8% infill

Designer

1.7 h

1 plate

5.0(5)

Divider 20mm 0.2mm layer, 2 walls, 8% infill

Designer

1.4 h

1 plate

4.3(3)

Click to see more

Boost

177

247

235

Released

Description

Made some addition for my spool shelf design, endcap for those whom wooden dowel extends from shelf bracket to prevent filament spool tipping over. It should fit tightly but I also included holes for M3 wood screw just to be sure.

Also made divider so you can separate different type of filaments from each other on one shelf and not mixing them accidentaly. Divider is just clip on, no additionl hardware required.

This all fits my spool shelf here with all different dimension wooden dowels, 20mm, 23mm and as well 1inch : https://makerworld.com/en/models/88779#profileId-95016

Comment & Rating (47)

@Michaelutsler

Print Profile

Endcap 1inch 0.2mm layer, 2 walls, 8% infill

pretty good design. looks great

The designer has replied

@Maoirae

Thank you, Im glad you like it.

@I3d4Prints

Print Profile

Divider 20mm 0.2mm layer, 2 walls, 8% infill

the quality doesn't seem to be quite as good as the brackets themselves but they don't necessarily need to be other aesthetically they match which is good enough for me but I thought I printed the 23 mm profile and it is not 23 mm. It comes out to 17mm. the hexagons themselves major 23 the portion that is to fit on your rod just like the brackets only measure 17 so you either have to trim them or the print needs adjusted

Other Issues:Dimension listed does not match Dimension that it prints out at

The designer has replied

@Maoirae

You must have chose wrong divider. because you printed 20mm version as you can see on photo

(Edited)

@I3d4Prints

so your reply answers the issue I have if I did select the 20 mm which I probably did it still only comes out at 17 so that's the issue the the hook part 17 on as you can see by my picture it's not right 17 is not 20 and obviously 20 is not 23😂

@Maoirae

Replying to @I3d4Prints :

You obviously dont understand how it works, you are supose to clip it to wooden dowel. Its smaler at entry for purpose so it hold nice and tight on dowel. It is bendy enough to slide it on dowel. Round diameter is right how it should be.

(Edited)

@TheCardiacCat

Print Profile

Divider 1inch 0.2mm layer, 2 walls, 8% infill

Great print, perfect fit. love that they aren’t super wide so they don’t take up too much room.

The designer has replied

@Maoirae

Im glad you like it

@rekk

Print Profile

Endcap 20mm 0.2mm layer, 2 walls, 8% infill

I'm probably going to reprint it in black, but it's a nice design to pair with the other brackets.

The designer has replied

@Maoirae

nice workplace 👌

@dustyd88

Print Profile

Endcap 1inch 0.2mm layer, 2 walls, 8% infill

Another perfect print! Spool shelves now complete. Loving how the colors turned out, I plan to do the same with the Hex wall organizers. So blown away with the X1C and PETG. Thank you!