AMS Lite Splitter for A1 by Deviian

Deviian

3D Printer>3D Printer Accessories

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.16mm layer, 2 walls, 15% infill

Designer

47 min

1 plate

4.9(157)

Boost

292

578

176

906

720

Released

Description

Model of a splitter for AMS Lite designed for using an external spool without constant disconnecting of the PTFE tube.

Designed for PTFE tubes with an outer diameter of 4 mm and an inner diameter of 2.6 mm. Same as used by BambuLab.

The openings for PTFE tubes are intentionally tighter; try to insert the PTFE as deeply as possible."

It is designed above the print head (see the photo, the length of the lower tube is approximately 40 mm).
Before installation, it is necessary to disconnect all PTFE tubes and thread them through the splitter."
It is necessary to insert the tubes firmly into the splitter to avoid tube falling out or filament jamming. Be cautious about tube crimping or potential breakage.

When not using an external spool, it is necessary to have the filament retracted outside the splitter. This will clear the path for filament from AMS. When using an external spool, it is necessary to do the same, simply rotate the filament spool.

Comment & Rating (176)

@PolyCraftLab

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

So simple yet so effective, been running this for a few weeks, done many prints using the setup in the picture, feeding the filament from the spools hanging above using the splitter

The designer has replied

@Deviian

I really like your setup.

@PolyCraftLab

Boosted

Replying to @Deviian :

Thank you! I use this filament hangar (https://makerworld.com/en/models/120259#profileId-129472) and haven't needed to use bearings or anything, even cardboard spools spin freely on them when feeding into the splitter

@OgiArts

Replying to @Deviian :

me to really good idea

(Edited)

@nirmata

Print Profile

0.16mm layer, 2 walls, 15% infill

Great idea perfectly implemented!

The designer has replied

@Deviian

Thanks! I'm considering an adapter that will better support it in the vertical plane.

@hapehutzler

Maybe I'm too stupid to print this part, but one hole is definitely too small. Or am I seeing this wrong?

The designer has replied

@Deviian

It's fine like this. The hole narrows to guide the filament more effectively.

(Edited)

@hapehutzler

Replying to @Deviian :

Thank you very much! No i´ve understand.

@lazzapao62

Great Job! Perfectly printed in PLA with no changes on the printer profile ! Very useful accessory I was looking for !

@faluethi108

Print Profile

0.16mm layer, 2 walls, 15% infill

Works great

(Edited)

@victorray

Works well, I really like the integrated pass-thru cable management. I printed in clear PETG with no issues. Seems to get the job done, thank you!

@trent

Boosted

Works great, printed on silent mode in translucent green petg.

@Rupe

Print Profile

0.16mm layer, 2 walls, 15% infill

it did give me a feed error once right after I installed it but haven’t tried to change filament to much since I put it in, it seems like it will do a great job on allowing me to easily throw tpu in without disconnecting anything

@LorenzCR

Print Profile

0.16mm layer, 2 walls, 15% infill

@Calle131

Print Profile

0.16mm layer, 2 walls, 15% infill

good design, thanks for sharing

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

AMS lite Top Mount for A1-V2(STP)

emo飞机

AMS lite PTFE connector

Tom

140

271

AMS Lite - Wall Mount System

WildWolf_3D

168

266

Illuminated AMS lite number badge caps - see gif

G3DS

106

213