Test your 3D printer v2 by 3DPrintinGreece.gr

3DPrintinGreece.gr

3D Printer>Test Models

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

0.1mm layer, 2 walls, 30% infill

Designer

29 min

1 plate

4.9(15)

0.12mm layer, 4 walls, 100% infill

Designer

22 min

1 plate

5.0(6)

Boost

212

157

Released

Description

Summary

after a lot of wishes we present the new smaller Test your 3D printer! version 2.

new version 3 here: https://makerworld.com/en/models/54359#profileId-56081

new features

saving 75% volume compared to version 1
only 2.52cm3. (Version 1, 2mm baseplate: 3.16cm3)
optimized 3D print font
higher resolution
wall thickness
this version is for 0.48mm extrusion width (more to come)

This is a hard to print testfile!
often you don't know if your printer is ready for complex files. with this file you have an easy option to check problematic printing/slicing stuff.

does your printer challenge this ultimative part?
check it out and get (almost) instant results.

these test are included in this very tiny file:

size: the object is 2x50x30mm (baseplate)
hole size: 3 holes (3/4/5mm)
Nut size: M4 Nut should fit perfectly
fine details: pyramide, cone, all numbers
rounded print: wave, half sphere
minimum distance & walls: 0.1/0.2/0.3/0.4/0.5/0.6/0.7mm
overhang: 25°/30°/35°/40°/45°
bridge print: 2/4/8/16/mm
surface: all the flat parts

version 1

Instructions

infill: 33% infill or similar
extrusion width: 0.48mm
layerheight: 0.1mm
print time: about 30 minutes, depending on your printer & settings
raft: you can use a raft

creation by ctrlV at Test your 3D printer! v2

Comment & Rating (23)

@JJeremy

Print Profile

0.1mm layer, 2 walls, 30% infill

A good test for your printer everything is good !! thx

@OddzWorldz

Print Profile

0.1mm layer, 2 walls, 30% infill

Print was fast and had no issues with the file. Fun and simple print to test your printer.

(Edited)

The designer has replied

@3DPrintinGreece

Hi, adhesion issues is not a print profile problem, as it is printed several times. Please change your review if you can and send me pictures to help you eith that. usually a good clean with soap and water solves the problem. wich print plate do you use;

(Edited)

@OddzWorldz

Replying to @3DPrintinGreece :

I was able to correct the problem I was having by drying out the filament and washing the bed in dawn soap. Thank you for reaching out to me I appreciate you.

(Edited)

@moppi

Print Profile

0.1mm layer, 2 walls, 30% infill

Nice little helper!

@bgioan

Print Profile

0.1mm layer, 2 walls, 30% infill

Perfect tester thanks

@momofatts

Print Profile

0.1mm layer, 2 walls, 30% infill

Great Test.

@janpeterkrumm

Print Profile

0.1mm layer, 2 walls, 30% infill

sehr gut, es zeigt die wichtigsten Einstellungen

@lmp1982

Print Profile

0.12mm layer, 4 walls, 100% infill

@physio

Print Profile

0.12mm layer, 4 walls, 100% infill

@Anya

Print Profile

0.1mm layer, 2 walls, 30% infill

@butrfingrz

Print Profile

0.12mm layer, 4 walls, 100% infill

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.