VOS - the Supply Ship
Copyright Claim
VOS - the Supply Ship
Boost
84
171
27
Print Profile(3)
0.08mm layer, 2 walls, 10% infill
3.1 h
1 plate
MULTICOLOR - 0.2mm layer, 3 walls, 15% infill
9.1 h
2 plates
FLOATS!!! 0.2mm layer, 2 walls, 35% and 15% infill
12 h
1 plate
Boost
84
171
27
0
354
341
Released
Description
Vos is a supply ship and carries goods from the mainland to an oil rig or other bases. The different charging options make VOS so universal.
Even if my boats are not benchmarks (benchy), you can use them for quality control.
The infill must be printed obliquely
The lower section has 35% infill, the upper 15%. For this purpose I have extended the surface layer to 6.
Multicolour was made possible by changing the filaments. As always with my Prusa and Slic3r, an M600 command was simply inserted in the appropriate places.
Dark red leaves layer - 0 - 9mm (Layer 0-45)
Red from - 9-36.00mm (Layer 45-180)
White from - 36.05mm - END (Layer 180-309)
Comment & Rating (27)
All
Print Profile
0.08mm layer, 2 walls, 10% infill
Nice ship! Some details were not perfectly printed. Don't know if it's only me.
0
Reply
does yours float upright?
0
Reply
Replying to @dustydumptruck
No, unfortunately not
0
Reply
Replying to @Toys_And_Stuff
i just made a new print profile. this one floats correctly
0
Reply
Mega cooles Boot! Meine Freundin hat noch passende Aufkleber geplottet 😊 Etwas größer gedruckt, kann man bestimmt ein RC-Modell daraus bauen 😁 bitte mehr Schiffe ...
The designer has replied
1
Reply
sieht ja mega aus 🤩
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
Cool
0
Reply
does yours float upright?
0
Reply
Print Profile
MULTICOLOR - 0.2mm layer, 3 walls, 15% infill
Almost flawless. Rear bottom had imperfections, otherwise cool print. .
(Edited)
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
the was a great file to print for me
0
Reply
Using the print profile on the project here and the boat instantly turns over in the water. I didn’t see that you have to print a different infill setting at an angle. idk how to do that in Bambu Studio but I assume that is needed to flat.
1
Reply
yeah i'm also kinda confused on this....why isn't the infill included in the print profile?
0
Reply
i just made a new print profile. this one floats correctly though it is kind of a long print.
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
The boat and it's accessories printed perfectly. Floats upright with no problem. I was able to print all parts using "by object" instead of by layer since I wanted to print them in different colors and not take forever.
0
Reply
can you explain how you did the infill? i printed using the ams profile and it instantly tilts to one side or the other and if you put anything in the cargo area it capsizes.
0
Reply
Print Profile
MULTICOLOR - 0.2mm layer, 3 walls, 15% infill
does not float!
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
Mega tolles Schiff, das lässt sich bestimmt auch vergrößern und als Rc Modell bauen 😃
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
My boys love these!
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld