Lego-compatible Baseplate 28x28

hollowmaker
Toys & Games>Other Toys & Games
Copyright Claim

Lego-compatible Baseplate 28x28

hollowmaker
Boost
169
365
32

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
Designer
4.8 h
1 plate
4.8(19)
Test-Baseplate - 0.2mm layer, 2 walls, 15% infill
Test-Baseplate - 0.2mm layer, 2 walls, 15% infill
Designer
13 min
1 plate
4.8(8)
Boost
169
365
32
2
316
310
Released

Description

Perfect fit for Bambulab A1, P1- and X1-Series: Lego compatible Base Plate 28x 28 knobs

 

  • 28x28 knobs - Dimension: 22,3 x 22,3 cm
  • I also have smaller baseplates available (check my Makerworld-account)

Attention! Important:
A well calibrated printer is absolutely necessary for this model (This also applies to all my other Lego compatible ones) 

If you print on a Bambulab: Before printing, be sure to carry out a flow dynamics calibration for the filament used. The calculated “K value” can be conveniently saved in Bambu Studio.

 

I added a test baseplate. For those who are not sure about the fit or quality and don't want to take a long time to print. Printing only takes a few minutes. Feel free to test it out:

Follow me to stay updated and never miss out on my latest exciting creations! Thank you :)

Also check out my other Lego compatible designs I have made:

lego
compatible
base
plate
baseplate
buildplate
brick
bricks

Comment & Rating (32)

Please fill in your opinion
(0/5000)
level
@olafejs
Boosted
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
Perfect !
The designer has replied
0
Reply
level
@hollowmaker
Thank you very much :-)
0
Reply
level
@g3n3zyp
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
good profile, printed successfully
0
Reply
level
@g3n3zyp
Print Profile
Test-Baseplate - 0.2mm layer, 2 walls, 15% infill
fast test, printed without issues
0
Reply
level
@VinceVega13
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
fits nicely. thanks for sharing.
The designer has replied
1
Reply
level
@hollowmaker
Thanks for the positive feedback :)
0
Reply
level
@user_127473009
how many top and bottom shell layers do you recomend for this?
The designer has replied
0
Reply
level
@hollowmaker
2 layers
0
Reply
level
@andrewrankin32
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
Legos are hard to get on and off
The designer has replied
0
Reply
level
@hollowmaker
Hi andrewrankin32. There is a possibility that your 3D printer is not 100% optimally calibrated. May I ask if you printed the model with a Bambulab where the flow dynamics were calibrated for the filament used? It can't hurt to repeat this to get optimal printing results in the future. If you like, print the “Test-Baseplate” - the Legos should be able to be put onto the baseplate relatively easily (and removed too). I printed and tested the model several times before publication until I was really satisfied with the quality and the feedback from the community so far has been very positive, so I assume there can't be much wrong with the model itself. Thank you very much! hollowmaker
(Edited)
2
Reply
level
@user_3157317357
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
had some lifting issues around the edges, otherwise good
0
Reply
level
@Flowster
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
Legofiguren und Bausteine passen perfekt drauf
0
Reply
level
@user_527841939
Print Profile
Baseplate 28x28 0.2mm layer, 2 walls, 15% infill
amazing print quality excellent file no issues
0
Reply
level
@user_295350096
Print Profile
Test-Baseplate - 0.2mm layer, 2 walls, 15% infill
made it in abs worped a liten but still worked . could be a bit (thicker).
(Edited)
0
Reply

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Brick Cactus

Brick Cactus

hollowmaker
0
9
9
JIGFINITY: Gridfinity Bin + Baseplate Magnet Jig

JIGFINITY: Gridfinity Bin + Baseplate Magnet Jig

robosquiggles
2
10
4
Nuka Cola LED Light - Kit001 compatible Fallout

Nuka Cola LED Light - Kit001 compatible Fallout

ChainsawGraphics
0
10
5
Autotray Lite - A1, P1 and X1 compatible
GIF

Autotray Lite - A1, P1 and X1 compatible

Darren
9
171
50
PrivacyTermsGuidelinesFAQCookie PolicyCookie Settings
© 2024 MakerWorld