Ikea Samla 22L - Filament Storage Box Remixed by Kroeskoppie

Remixed by

Kroeskoppie

3D Printer>3D Printer Accessories

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

0.20 mm layer, 3 walls, 10% infill.

Designer

9.9 h

5 plates

4.7(25)

Boost

136

241

490

Released

Description

Original Source Material:
- Original Creator Ikea Samla Foam Clips: 3Dpartmaker on Thingiverse.

- Original Creator Ikea Samla Silicagel Box: Grizmo on Thingiverse.
- Original Creator Ikea Samla Drybox Sensor Mount: RoboMagus on Thingiverse.

- Original Creator Ikea Samla Gliding Feet: Physicator on Thingiverse.
- Original Creator 10 mm Rod Holder: CCoonz on Thingiverse.

Please support all these great designers! Thank you for your work!

Description:
A remix & share for a complete Filament Storage Box by using multiple models from multiple sources. A Ikea Samla 22L box is used, as these are available around the globe. I edited the 10 mm Rod Holder to fit my specific needs. I have multiple Ikea Samla boxes that use this complete setup to keep my filaments free from dust and moisture. Also, Gliding Feet are added to the Samla Box to avoid damaging the floor and to easily move the boxes around.

The 10 mm rod holders have been remixed by me to make it able to use in combination with the Silicagel Box. The rod holder was edited in Tinkercad for that. It was firstly uploaded on Printables on 24-04-2023.

To complete this setup, you will need to buy some extra stuff:
- 4x M3 Bolt, 16 mm in lengte. I like to use a PZD Bolt for easy screwing and this fits nicely.
- 4x M3 Nut.

- Self-adhesive foam tape for extra sealing the lid.
- Doublesided self-adhesive tape for mounting the rod holders.

- A 10 mm rod. I like to use aluminium rods. Must be cut to the right size.
- A round hydrometer. These can be bought cheap on Alieexpress.
- I like to add some soft, self-adhesive felt on the gliding feet, but this is completly optional.

Some small instructions on some of the printable parts:

----Ikea Samla Foam Clips----

Please add a brim to the printing profile when printing the clips for good adhesion to you build plate. Otherwise, the print may fail!

----Ikea Samla Drybox Sensor Mount----

M3 Bolt have quite a tight fit. Use some pliers to force the M3 nut in.
Use a 3 mm drill for drilling the holes in the Samla box.

----Ikea Samla 10 mm Rod Holder----

The screwholes from the original design are still available, but I can find screws that are long enough. I like to use Doublesided self-adhesive tape for good mounting.

I did the following in Bambu Slicer for all the models:
- I used a 0.20 Print profilebasefile I like and edited it.
- I sorted all the different parts on different plates for easier printing, based on the colors I liked..
- The printing profile has Brim turn off by default. I would highly recommend to use a brim when printing the clips.

If there are more suggestions for better settings, please upload them!

The color sorting in the 3fm-file is based on the following filament that I used for this print:
- White: eSUN PLA+ Cold White.
- Grey: eSUN PLA+ Grey.

Please note that eSUN is currently switching to Carton Spool Holders if you want to print from the AMS-System. I used the ‘old’ plastic filament spools which I currently still have.

Comment & Rating (32)

@marcmaster2009

Print Profile

0.20 mm layer, 3 walls, 10% infill.

Nice Design easy to print

@BodenM

Just printed one for myself and love it. Printed all from FormFutura rApollo ASA filament in white, fitment is spot on. To make installation easier I ended up drilling out the holes in the hygrometer mount out with the same 3mm drill bit I used to drill through the box.

@user_4225639205

Print Profile

0.20 mm layer, 3 walls, 10% infill.

Passt alles perfekt, vielen Dank für teile, bin begeistert, hoffe das ich sowas auch mal hinbekomme zu Designen, bin noch Anfänger 😅🤪

@chrsmth

Hey. Darf ich fragen welche Samla-Box genau du verwendet hast? Evtl. hast du einen Link? 🙂

@user_4225639205

Replying to @chrsmth :

hab dir ein Bild, da steht der Name usw, leicht zu finden, echt perfekt 👍Grüße Peter aus Stuttgart

@cblte

THIS. IS. THE. BEST. THING. EVER! Thank you so much. I was trying to find here and there something I could put together. Found all the original projects, but you did the best job of combining them all in on! Thank you so much! - Filament used for the **Box, Stands, Hygrometer holder: ** SUNLU PLA+ White: 0.20 Layer, 15% infill, 3 walls, 220 ºC** - Filament used for the clips: **fill 3D PETG Orange, 0.20 Layer, 15% infill, 3 walls, 250 ºC** I was able to use M3 screws without the counter-hex nut. Maybe I will add one, but since the holes are quite tight, the screws work even without a counterpart. 👍 Hint for drilling the holes: I initially used one of the bottom feet as a measurement, but ended up just going 2.5cm from the top and did a rule-of-thumb 🤙 estimate to center it. Edit: I forgot to add some filament information. Now added

(Edited)

@janpeterkrumm

Print Profile

0.20 mm layer, 3 walls, 10% infill.

top, passt sehr gut und ist einfach zu drucke .

@chrsmth

Hey. Darf ich fragen welche Samla-Box genau du verwendet hast? Evtl. hast du einen Link? 🙂

@chalkin

This is awesome. Works well with the IKEA Boxes. I used Overture Matte PLA. Had to change the Printer Profile to my P1P. Thanks so much. Using it in two boxes now.