Flipper Zero Case - Silicone Edition
Remixed by
Copyright Claim
Flipper Zero Case - Silicone Edition
Remixed by
Boost
32
69
17
Print Profile(2)
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Designer
3.8 h
2 plates
Textured Plate - 0.2mm layer, 2 walls, 15% infill
Designer
3.8 h
2 plates
Boost
32
69
17
0
87
104
Released
Description
This a my remix of the Flipper Zero Case. I had to make my own remix because all the Printable models were giving me errors when attempting to slice them in PrusaSlicer (prior to getting my X1C). This case allows you to store your Flipper Zero with the silicone case on it. The top lid has a cut out so you can insert the stock foam and USB cable. Underneath the USB foam in the top lid is a cut out for SD Card storage as well. Please leave a comment and rating if you enjoy this remix!
Additional parts needed for this build:
- 4x M3 x 20mm (front hinges)
- 2x M3 x 16mm (rear hinges)
The edits I made were:
- Added the insert so you can fit a FZ with a silicone case.
- Added missing front bezel to top lid.
- Added SD Card text to inside of top lid.
Comment & Rating (17)
All
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Great Model. Works as the profile is explained. Had a bed adhesion issue but was my own doing, luckily it didn't affect the final product or require any re-makes
The designer has replied
1
Reply
It came out great. Thanks for the rating and feedback!
0
Reply
perfect!
1
Reply
Print Profile
Textured Plate - 0.2mm layer, 2 walls, 15% infill
muy bonita y mi flipper zero protegido 😉👍
1
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
looks great! thanks for the rating 🤘🏻
0
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Printed Great in two color ABS. Very strong, Very useful. Thanks for the shape! I made a gasket for it that works in TPU and does seal it a little. Contact if you want to add it to your project.
(Edited)The designer has replied
1
Reply
Awesome! thanks for the positive feedback. Feel free to add the TPU gasket as a print profile and I'll update the description.
0
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Printed in translucent gray and orange PETG. Came out great. Tolerances on the hinges and latch are perfect for the m3 screws without nuts.
The designer has replied
1
Reply
Thanks for the rating and feedback. Good tip, I didnt use nuts either. I figure if they ever loosen, I can just add a bit of glue at the end of the thread and itll be good.
0
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
perfect
1
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Awesome case!
1
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
Great box for the Flipper Zero!
1
Reply
Print Profile
High Temp Plate - 0.2mm layer, 2 walls, 15% infill
fits perfectly with foam insert
1
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld