Middle Finger Wand - collapsible/telescoping middle finger by Joe Wilson

Joe Wilson

Art>Sculptures

GIF

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

*** FIXED Dual Colour 2 HOURS *** 0.28mm layer, 2 walls, 10% infill

Designer

2.2 h

1 plate

4.2(80)

*** FIXED Single Colour 1 HOUR 36 MINS *** 0.28mm layer, 2 walls, 10% infill

Designer

1.7 h

1 plate

4.0(31)

Boost

309

449

130

924

712

Released

Description

Improved model here - https://makerworld.com/en/models/146096#profileId-159063

This is a telescoping/collapsable Middle finger ready for whenever your annyoing brother walks in your room.

Comment & Rating (130)

@jldeen

Print Profile

*** FIXED Dual Colour 2 HOURS *** 0.28mm layer, 2 walls, 10% infill

I really wanted to like this. I tried printing twice, including the latest profile… the first time the print came off the bed. The 2nd time it printed, but pieces snapped off when the bed cooled down. Also top layers are definitely stringy. New supports use quite a bit of filament too and doesn’t seem to fix the issue.

The designer has replied

@joewilson09

hi I made a new model, check the description of this model and there is a link to a newer updated model

@jldeen

Replying to @joewilson09 :

That’s the model I used.

@joewilson09

Replying to @jldeen :

no that’s the old I’m pretty sure, the screw on middle finger

@Santi

Print Profile

*** FIXED Single Colour 1 HOUR 36 MINS *** 0.28mm layer, 2 walls, 10% infill

what a mess…. prited from bambu handy app p1p

(Edited)

The designer has replied

@joewilson09

Sorry about this, its due to the very small surface area of that middle section so its hard to get this model to stick the whole way

@joewilson09

i fixed the issyue now in the print rpofile

(Edited)

@esbenjensen2

Print Profile

*** FIXED Single Colour 1 HOUR 36 MINS *** 0.28mm layer, 2 walls, 10% infill

the hans want loose, gonna try again.

The designer has replied

@joewilson09

if your still hvaing issues check out my new updated model here which shoiudl work better https://makerworld.com/en/models/146096#profileId-159063

@Fvcksimile

Print Profile

*** FIXED Single Colour 1 HOUR 36 MINS *** 0.28mm layer, 2 walls, 10% infill

Nice project but maybe a little too delicate, in the end a rod came off and started to vibrate ... too bad, I'll try again

The designer has replied

@joewilson09

if your still hvaing issues check out my new updated model here which shoiudl work better https://makerworld.com/en/models/146096#profileId-159063

@Fvcksimile

for me nothing.... brake it in final layers... mmmm

The designer has replied

@joewilson09

i have now fixed it in the print profile

@nathanellevi

Print Profile

*** FIXED Dual Colour 2 HOURS *** 0.28mm layer, 2 walls, 10% infill

turned out amazing this is so funny

@user_3822245831

you’re lucky my app didn’t recognize I made your print with my Neptune max or I’d give you a one star. I’m upset this print file is still on here and you made a newer version that isn’t in the description and I had to find out after I started this 3 day build in the comment section. long last the print finished and I was excited I full extension the hand but had to tap it handle first on the floor to get it to retract them the whole thing slowly fell out of my hand and all it did was tip over and landed on the rug! and broke off! I got one F You out of this and it should have went to your weak A”” wrist infill. bro look at this nonsense! what a waste of so much filament. I guess I can use it as a nose picker now or tempature probe