V. 3.0 - Shield with magnet
Remixed by
Copyright Claim
V. 3.0 - Shield with magnet
Remixed by
Boost
32
56
41
Print Profile(4)
SX 8x3mm 0.2mm layer, 2 walls, 15% infill
Designer
49 min
1 plate
DX 8x3mm 0.2mm layer, 2 walls, 15% infill
Designer
49 min
1 plate
SX 10X3mm 0.2mm layer, 2 walls, 15% infill
Designer
1 h
1 plate
DX 10x3mm 0.2mm layer, 2 walls, 15% infill
Designer
1 h
1 plate
Boost
32
56
41
0
212
153
Released
Description
07/01/2024 new version 4.0
https://makerworld.com/en/models/128344#profileId-138948
This is my new 3.0 project with these features:
simple
fast
smart
with magnets 10x3mm, 8x3mm
Comment & Rating (41)
All
Fits really well, only problem is that I am getting grease on my sleeves again because the screws are exposed. Going to go back to V2
The designer has replied
0
Reply
thanks for the feedback.
This was designed smaller for speed and ease of printing.
Based on this I try to create another one with slightly longer walls.
0
Reply
Replying to @FrancescoM
When can we expect longer walls on this? I printed 8pcs of the V2 for my 2 printers. first 4 failed and then next 2 failed as well. The print wobbles like crazy when reaching the top part. V3 wall still leaves the lead screw exposed so that's not good.
0
Reply
Print Profile
SX 10X3mm 0.2mm layer, 2 walls, 15% infill
calza a pennello,perfetto!!
The designer has replied
0
Reply
Thank you for great rating
0
Reply
Print Profile
SX 8x3mm 0.2mm layer, 2 walls, 15% infill
works
The designer has replied
0
Reply
Thank you for great rating
0
Reply
Print Profile
SX 8x3mm 0.2mm layer, 2 walls, 15% infill
Fits great on my P1S
The designer has replied
0
Reply
Thank you for great rating
(Edited)1
Reply
Print Profile
DX 8x3mm 0.2mm layer, 2 walls, 15% infill
Fits great on my p1s
The designer has replied
0
Reply
Thank you for great rating
(Edited)1
Reply
Nice design, thank you.
For some reason the bed adhesion under the support part was off, but after adding some brim and reslicing it worked.
Also I just managed to buy 50pcs of 3x6 magnets, so I will print some extender rings to make them fit.
Thanks again.
(Edited)The designer has replied
0
Reply
then use for glue to hold your magnets
0
Reply
Print Profile
SX 10X3mm 0.2mm layer, 2 walls, 15% infill
Lässt sich hervorragend drucken und wertet den Drucker optisch auf.
The designer has replied
0
Reply
Vielen Dank für die hervorragende Bewertung
0
Reply
Print Profile
DX 10x3mm 0.2mm layer, 2 walls, 15% infill
Worked great. Better than the other models I had tried.
The designer has replied
0
Reply
Thank you for great rating
0
Reply
Print Profile
SX 10X3mm 0.2mm layer, 2 walls, 15% infill
Worked great. Better than the other models I had tried.
The designer has replied
0
Reply
Thank you for great rating
0
Reply
Print Profile
DX 8x3mm 0.2mm layer, 2 walls, 15% infill
good model
The designer has replied
0
Reply
Thank you for great rating
0
Reply
Remixes (1)
Related Models
© 2024 MakerWorld