Utility OG case by sipura

sipura

Tools>Organizers

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 2 walls, 12% infill

Designer

10.3 h

4 plates

4.9(124)

V2 with thicker hinges 0.2mm layer, 3 walls, 12% infill

Designer

9.8 h

4 plates

4.9(95)

Inner box for the upper part of the case

Designer

2.5 h

1 plate

4.7(22)

0.2mm layer, 2 walls, 15% infill

4.3 h

1 plate

5.0(1)

Boost

1423

2529

360

3 k

4.4 k

Released

Description

Hello,

UPDATE 26/1/2024:

You can check you our new model, same like this one but XL bigger. Inner containers are compatible.

https://makerworld.com/en/models/157759#profileId-173134

UPDATE 19/1/2024:

You can check you our new model, same like this one but smaller. Inner containers are compatible.

https://makerworld.com/en/models/146935#profileId-160286

My new model of the utility case.

Simple print without support

All parts are completely printed with PLA, only the gasket needs to be printed with TPU in order to close smooth and seal nicely.

To assemble it, you need:

6pcs M3 nuts

2 pcs of screws M3x30

3pcs of screws M3x18

Dimensions are in mm:

NEW:

Now we made V2 model that has thicker hinges on each side by 1mm behind, and wall loops with 3pcs.
For this model, instead of 3pcs M3x18mm screws, you now need 3pcs M3x20mm.

Also, if you need some custom accessories for all our models, you can contact us on our patreon page which is in bio.

Enjoy printing and using this useful case.

Comment & Rating (360)

@user_1013152695

Thanks for your share, and TPU fliament can be used directly. Exactly fit!

The designer has replied

@sipura

Nice, didnt know that... I recommend a print tpu seal to close smoothly, but if it works that way then great :D

@amdonio

Replying to @sipura :

Indeed fits perfectly without printing!

(Edited)

@sipura

Replying to @amdonio :

Great :D

@abweber

Print Profile

0.2mm layer, 2 walls, 12% infill

Great model, just the right size for what I needed. I added the lettering to the top, and it printed fantastic. I'm only knocking it because one of the hinges on the lower box broke when I was assembling it. It broke on a layer line, so I think it could be redesigned to be a little stronger by making it a little beefier. I am going to reprint that piece with 3 or 4 perimeters instead of 2 and see if it is stronger.

(Edited)

Strength Issue

The designer has replied

@sipura

Thank you for your honest review. It's a bit strange to me, because this is the v3 model that I made with stronger hinges and it works perfectly for me, with a lot of use. Anyway, I made a new model and published a separate profile with 1mm thicker hinges on each side, and I hope this one will suit you better. Consider that you now need M3x20mm screws for that model instead of the previous 18mm. In the picture you can see the parts marked in red, they are made thicker. Best regards

(Edited)

@abweber

Replying to @sipura :

That's fantastic, thanks! I will go ahead and print the new one tonight. I sliced off the top corner of the model so I could do several faster test prints with different settings. Between upping the wall loops to 3, and upping the temp to 240, it was significantly stronger. I estimate that it was 2-3x as hard for me to break the hinge section off with these settings. Usually the default settings for the X1C are good enough for my prints, but in this case I needed to tweak for more strength.

(Edited)

@ernesdts

how do you made those letters? :0 I have an AMS but I never achieaved that kind of multicolor in a single layer

@ReturntoSender7

Print Profile

0.2mm layer, 2 walls, 12% infill

An amazing box! I designed some inserts so I could store spare bulbs and fuses for my VW camper

The designer has replied

@sipura

Nice one👍

@Thatguyadz

Print Profile

0.2mm layer, 2 walls, 12% infill

Absolutely love this box.... great design. I'm using mine to store all of the little Bambu bits & bobs.

The designer has replied

@sipura

Nice, color combinations are great too :D

(Edited)

@Thatguyadz

Replying to @sipura :

Thank you. Currently printing the larger one. will share pictures once finished. Love you're work keep it up. 🔥

(Edited)

@LitoPine

Could you make a case with these dimensions? They are listed in the photo. Those would need to be internal dimensions.

The designer has replied

@sipura

Thank you for the suggestion. This was the first one we made and published, after this we made and published a smaller model that you can find in my profile. We are already working on a larger model, which should be twice as big as the first version, but the inner boxes should be modular and correspond to the old model.

@sipura

That will be the dimensions for the new one. 194x188x64mm 64mm will be the hight. The reason for such dimensions is that all the boxes are modular, and that the inner boxes from, for example, smaller ones fit into the largest box.

(Edited)

@LitoPine

Replying to @sipura :

I'm looking to only print the case with nothing on the inside. I would like to print it in ASA to be used in a marine application. I do not need any inserts.

@drozdovdanilsss

Print Profile

V2 with thicker hinges 0.2mm layer, 3 walls, 12% infill

printed in Bambu ABS.

The designer has replied

@sipura

nice :)

@user_1348643270

Thank you . Beautiful n easy to print . No support is need.

The designer has replied

@sipura

glad you like it. thanks :)

@BroerWolf

Boosted

Print Profile

0.2mm layer, 2 walls, 12% infill

Ran out of filament so made it a two tone. Also printed the remixed/printable plugs for the hinges. It's a great little rugged box that is very solid and looks stunning but takes a while to print tho. It now keeps all the spare parts and tools for my printer. Love it ❤️