The one ring - The Lord of the Rings
The one ring - The Lord of the Rings
Boost
716
1134
159
GIF
Print Profile(3)
v2 - 0.12mm layer, 2 walls, 15% infill
Designer
7.9 h
2 plates
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
Designer
7.6 h
2 plates
v1.1 - 0.12mm layer, 2 walls, 15% infill
Designer
6.9 h
1 plate
Boost
716
1134
159
13
1.1 k
793
Released
Description
The one ring, need I say more?
Hang on the wall or just put it on a table. The ring is a whole 160mm in diameter!
I printed with Bambu PLA silk - Gold.
Current version 2.0 - Now better shine!
Warning, the new back plate is much more secured when inserted. Make sure led is installed before closing.
The assembly is easy, just take about 50cm led strip and put it in the ring, like this:
Or alternative slide it in above the internal “bride”, this way you can get two loops for more light.
Revisions:
v 2.0
Total redesign of the inner space of the ring and the back plate. The led strip is now held in place which gives a more uniform shine. Slightly bigger radius on the top of the ring.
The back plate also snaps to the ring better, DON'T PUT ON UNTIL LED IS INSERTED.
v 1.1
- Added a optional back plate that snaps in place. Use the chord for hanging on wall, or drill a hole for a nail (or use bambu studio and add a hole)
Comment & Rating (159)
All
I Can't Get It To Print, Have tried At least 4 times and no go, i did scale it up to 150% and printed it 3 times, then i re downloaded it again, tried at 100% and still no dice, so i think everyone here, there pants are on fire!!!
The designer has replied
0
Reply
Hey man, sad to hear :( But, at a quick glance I can se you have sliced it yourself. For one, you should absolutely not use support and I can see both have internal support! Second, did you properly dry your filament? Third, weird accusation when there is so many others pictures with successful prints.
Recommending, dry your filament! Slow down print speed, don't use supports.
9
Reply
first thing off, “sliced it myself” what the fuck dose that mean? I downloaded the file off maker world, just like everyone else, second I had the Filament in my dehydrator for 24 hours, so, no, that is not the problem! I think the problem is in the file!!!
0
Reply
and I used supports because I scaled it up!!
0
Reply
Print Profile
v1.1 - 0.12mm layer, 2 walls, 15% infill
schwarz war nicht die beste Wahl 🤣
5
Reply
Dabeisein ist alles 😂😂😂👍
0
Reply
Replying to @ChristoT
lol safe ja 🤣
0
Reply
Very nice! Printed with Sunlu Gold Silk PLA and a light strip from Amazon...
The designer has replied
4
Reply
looks great! I think you used a better ligth strip than me.
0
Reply
which light strip did you use - do you want to share the link? thanks in advance
0
Reply
Replying to @mreichert75
Lepro Bright White LED Strip Light 10M (2x5M), 2x2300lm 6000K LED Tape Light, Stick-on LED Lights for Kitchen Under Cabinet (12V Power Supply Not Included) https://amzn.eu/d/hy47BCW
3
Reply
Great model! Printed in gold silk PLA and attached to a carved wooden board. The small "button" below is a SR-602 PIR sensor which activates the light glow for a minute when motion is detected.
The designer has replied
3
Reply
wow, love the idea! imma make one!
0
Reply
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Printed very well. had some ringing but I guess there is no way around it unless you slow it even further
The designer has replied
1
Reply
how fast did you run? have not seen that kind of ringing on mine or others prints.
0
Reply
u might wanna tune your flow rate because it looks almost like a layer shift however it wouldnt have been 50 layer shifts so... possibly over extrusion. another option would be to download orca slicer and try out the feature called "accurate exterior walls" just a thought
0
Reply
Print Profile
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
Printed with no issues. Used Sunlu silk gold pla
The designer has replied
1
Reply
looks great!
0
Reply
Yes I like it, thanks for sharing your model!
(Edited)2
Reply
Print Profile
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
I would appreciate, if with another version, the LED strip is placed on the extra rim, facing upwards, so it is less visible inside the ring (see pic) and light diffuses more evenly.
but still amazing print, model and thanks for sharing 🙏
(Edited)
The designer has replied
1
Reply
tried to solve it, somewhat, with v2.
0
Reply
Boosted
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Very nice, add a 2m cob-light with 5V insight
The designer has replied
1
Reply
thanks fellow winner! :)
(Edited)1
Reply
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Looks great.
(Edited)
2
Reply
Print Profile
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
printed with 0.16 layer with no issues.
2
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld