Light Saber Lite (Collapsible) | LS01 by SavageLau

SavageLau

Toys & Games>Other Toys & Games

Print Profile(2)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

colored, internal, external, cap&base in separate plates

Designer

5.9 h

3 plates

4.7(7)

Single color, internal & external parts in separate plates

Designer

4.9 h

2 plates

4.0(13)

Boost

122

175

348

496

Released

Description

If you want a commercial license, check out my bio and get it from Patreon.

This is simple version of Ultimate light sword. For people who does not want to have all the CAT light things in there. Just an simple Saber design. This is first one of my series of saber desing.

This Saber takes around 4h35m to print on X1C, takes around 105g of filaments.

Material Suggestions:

I Highly suggest to use Glow in the dark filament or Translucent filament for the internal parts, and pick any color you like for the external shell.

For external parts, DO NOT USE SOME BRITTLE silk filaments, it will break very easily. Some silk filaments will have very poor layer adhesion due to high speed printing cause part failure.

Post Work:

You will need to remove brims on both internal and external parts. Brim was added on all the printing profile to ensure the printing success rate. Print without brim is not recommaned.

Installation:

After you clean all the brims. follow these steps show on the gif.

Design:

This is a simple version of the ultimate light sword. I made a few design change on both internal and external to improve overall printing quality and have a slight different look.

Comment & Rating (26)

@Hero

Print Profile

colored, internal, external, cap&base in separate plates

Project are great and look awesome. Fast print but had problems with model that can't slice "smooth" and causing brim on side.

@prototypefab

hello, do you know if this would work scaled down? I'd like to print something like this for a kid, so I'd want it to be smaller, but i also like this more over your wands because you can swap broken inner pieces, which are gonna happen often if given to a kid

The designer has replied

@SavageLau

80% to 100% should work

@TomdeGroot

This is very cool!

@user_3630610590

Boosted

terrible every thing got stuck it’s pain really bad waste of filament

@chefk85

Fun design. My kid loves it. The first big segment tries to pop out though so maybe could ad a couple little tabs or make it thicker at the base to keep it from sliding out so easily. Printed on Bambu p1s

@Oliverm769

Print Profile

Single color, internal & external parts in separate plates

Great model! worked well the first time

@gheorghita.cris

Print Profile

Single color, internal & external parts in separate plates

the segments need a bit of redesign because they will not hold too many uses. the design is great.

@tania_made_

Print Profile

Single color, internal & external parts in separate plates

printed grate on my A1 zero problems

@OzzyMuppet

Tried to print the extending part 3 times now, but each time the 2 inner rings get loose, and start getting thrown around by the print head. I've used a huge brim which keeps the 2 outer layers stuck down, but those inner ones (even with inner brim) keep getting lose around the 1.5 inch mark... any tips? Have only tried with PLA Glow filament so far.

@user_3546828660

Print Profile

Single color, internal & external parts in separate plates

(Edited)

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.