F16 Kit Card
Copyright Claim
F16 Kit Card
Boost
306
582
45
Print Profile(2)
Large Model Pieces -- 0.16mm layer, 2 walls, 100% infill
Designer
4.8 h
1 plate
Small Model Kit Card -- 0.16mm layer, 2 walls, 100% infill
Designer
3.6 h
1 plate
Boost
306
582
45
1
702
347
Released
Description
Overview
F-16 kit card
Check out the SR-71, B-52, A-10, 787, and Darkstar!
Check out the full airplane kit card collection → linked here!
Profiles
- Small Model Kit Card
- Small plane in a kit card ideal for gifting to others
- Small Model Pieces
- Small plane without kit frame ideal for print & build
- Large Model Pieces
- 142% Scale to go BIG! Large plane without kit frame ideal for print & build
- Small Model Kit Card (A1 Mini)
- Add mini support for kit format
Filament
As shown:
- Esun PLA+ Gray
- Hatchbox Cool Gray
Tips
- Model requires close tolerances to ensure snug but not tight or loose fit
- Make sure the model cools to room temperature before assembly
- Ensure filament is properly calibrated with no excessive over extrusion
- Ensure good bed adhesion
- Make sure printer is fully calibrated
- Make sure print bed is clean & dry (soapy water is my favorite for cleaning - simple & works)
- Make sure filament is dry (wet filament can generate non-continuous flow that can cause bed adhesion issues)
- Cooling & Temps - make sure they are correct for your printer, build plate, and filament
Assembly
- Remove all pieces from the kit
- Debur as needed to smooth edges
- Glue tank together (optional but recommended)
- Glue missile together (optional but recommended)
- Let glue cure before proceeding to next step (optional but recommended)
- Insert wing into forward fuselage slot
- Insert tail into aft fuselage slot
- Insert tank pylon to wing
- Recommend aft end first, then press down softly on forward end. It will clip into place. (See gif below)
- Recommend aft end first, then press down softly on forward end. It will clip into place. (See gif below)
- Insert missile pylon to wing
- Recommend aft end first, then press down softly on forward end. It will clip into place. (See gif above)
- Place airplane onto stand
- Enjoy!
Comment & Rating (45)
All
Print Profile
Large Model Pieces -- 0.16mm layer, 2 walls, 100% infill
Turned out nice 👍🏼
The designer has replied
1
Reply
thanks for sharing your awesome print!
(Edited)1
Reply
Print Profile
Small Model Kit Card -- 0.16mm layer, 2 walls, 100% infill
It printed perfectly, a great gift for someone who likes planes or a fun project!
The designer has replied
1
Reply
Thanks! This black looks great on these. Will need to add one to my own collection!
0
Reply
Print Profile
Large Model Pieces -- 0.16mm layer, 2 walls, 100% infill
this is really cool, my son likes it, thank you for posting!
The designer has replied
1
Reply
welcome! looks awesome!
(Edited)1
Reply
Print Profile
Large Model Pieces -- 0.16mm layer, 2 walls, 100% infill
0
Reply
Print Profile
Small Model Pieces -- 0.16mm layer, 2 walls, 100% infill
very nice
The designer has replied
1
Reply
thanks!!
0
Reply
Print Profile
Large Model Pieces -- 0.16mm layer, 2 walls, 100% infill
Beautiful model. Went together great.
The designer has replied
1
Reply
thanks! glad you enjoyed it!
(Edited)1
Reply
Print Profile
Small Model Kit Card -- 0.16mm layer, 2 walls, 100% infill
Really great looking model!
The designer has replied
1
Reply
thanks!
(Edited)1
Reply
Print Profile
Small Model Kit Card (A1 Mini) -- 0.16mm layer, 2 walls, 100% infill
thank you! it turned out nice.
1
Reply
Print Profile
Small Model Kit Card -- 0.16mm layer, 2 walls, 100% infill
I tried multiple times with different type of filaments. I can’t print this model
0
Reply
Replying to @planes01
first layer is adhesion issue. I don’t think it’s about the filament calibration or dirty bed. Because I tried to print something else after this model fails. all the time I can print them very well
0
Reply
Print Profile
Small Model Kit Card -- 0.16mm layer, 2 walls, 100% infill
awesome model, thank you
1
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld