Brick / Block Style Dust Plug for X1 and P1 Printers
Copyright Claim
Brick / Block Style Dust Plug for X1 and P1 Printers
Boost
60
115
49
Print Profile(1)
0.16mm layer, 2 walls, 15% infill
Designer
27 min
1 plate
Boost
60
115
49
3
180
163
Released
Description
If you love famous Bricks, this is great addition for you 3D printer!
Please note: Do not stack blocks to high, as the belt is just above it. L* figurine fits perfectly there is lots of clearance above.
***** Ignore stars rating - It is user error - Model is fine. I made 5 different prints (different materials and plates) one print was sent from phone, other 4 from bambulab studio, all printed successfully. ******
Comment & Rating (49)
All
Didn't fit!
The middle plugs was coming in contact with the bottom of the middle holes.
Cut of the middle plugs and now it fits.
3
Reply
I had ro the same thing
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Printed fine but this does not pop into place. You got one side snapped into place and the otherside gets popped out.
The designer has replied
1
Reply
this is not a model issue. most likely during print you bed adhesion was bad and it started bending during print. there are over 200 downloads and no one reported this issue. I made myself 3 in different colors and they all stay in
or other issues may be that you didn't clean support properly.
edit: I am printing another one on different plate just to check if maybe prints differently on this plate.
(Edited)1
Reply
Done. It didn't pop out. it sits tight and secure on both sides.
btw while I was removing support I noticed that model may bend while you were removing support.
anyhow this is not model issue but user issue. so definitely this doesn't deserve to get only two stars.
0
Reply
Boosted
Print Profile
0.16mm layer, 2 walls, 15% infill
Snapped right in and my 80's era space fellows are now in position, ready to improve future 3d prints :-)
The designer has replied
1
Reply
I love Lego's from 80's I have some too
Thank you for rating. I love seeing what kind of figurines people use in their printers.
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Nice little touch for my 'MANDO' X1C. Great print in Eryone PETG Black
The designer has replied
1
Reply
Looks great! Thank you for download and rating!
0
Reply
so cute
2
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Printed with ASA and scaled to 101% it's a perfect fit.
The designer has replied
0
Reply
This is photo from something else
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Very good!
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Nice print, fitment appears similar to OP. Support peeled off carefully by hand.
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Such a cool idea. I’m awaiting a “brick” Walter White and Jesse Pinkman in HASMAT suits to arrive so they can watch the SCIENCE!!
The designer has replied
1
Reply
share the pictures once you do. :)
(Edited)1
Reply
Replying to @AstraCD
Will do!
0
Reply
Can we get the photo now please?
0
Reply
tried printing it and didnt come out great for me but love the idea :) may i will try tpu
The designer has replied
1
Reply
What was the issue? I am planning to make version two, so I can add improvments.
0
Reply
Replying to @AstraCD
it doesnt sit very flush and the round inserts are a little tight also my lego guy didnt fit very well but they maybe to my settlings perhaps :)
1
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld