30秒即可将千分表固定在拓竹x1/p1系列打印机的工具头上，你可以使用它对设备热床手动调平。

The dial indicator can be fixed on the tool head of BAMBULAB X1/P1 series printer in 30 seconds, and you can use it to manually level the hot bed.

它有以下优点：

1.不需要拆掉热端以及挤出机 。

2.将其固定在挤出机时不需要内六角扳手外的任何工具。（将背板安装在千分表上时需要一把十字螺丝刀）

3.固定稳定，不易晃动。

它有以下缺点：

1.它只能固定在tz1.0热端散热鳍片上或者拓竹原装热端，我提供了stp文件以供调整。

2.60度以上的热床手动调平需要使用耐高温材料打印：如abs，asa等，否则环境温度容易使其变形。

It has the following advantages:

1. There is no need to disassemble the hot end and extruder.

2. No tools other than an Allen wrench are required to fix it to the extruder. (A Phillips screwdriver is required when mounting the back plate to the dial indicator)

3. Fixed and stable, not easy to shake.

It has the following disadvantages:

1. It can only be fixed on the tz1.0 hotend cooling fin or original hotend, so I provide the STP file for adjustment.

2. Manual leveling of hot beds above 60 degrees requires printing with high-temperature resistant materials: such as abs, asa, etc., otherwise the ambient temperature will easily cause it to deform.

使用说明：

1.将千分表背面四颗螺丝拧下来，把原来的背板替换为打印件。（注意朝向）

2.拆下工具头散热风扇，拔掉风扇插头。

3.使用内六角扳手将图1指出的那颗螺丝拧下来，后面会使用到。

4.对准位置，将千分表卡入热端散热鳍片中，（鳍片没对准不要硬来，位置正确背板可以靠到挤出机）

5.把第一步拆下来的螺丝塞到背板上方的孔洞里，用螺丝扳手拧进去。

Instructions for use:

1. Unscrew the four screws on the back of the dial indicator and replace the original back plate with the printed one. (note the direction)

2. Remove the tool head cooling fan and unplug the fan plug.

3. Use the Allen wrench to unscrew the screw pointed out in Figure 1, which will be used later.

4. Align the position and insert the dial indicator into the hot end heat sink fin. (Don’t force it if the fin is not aligned. If the position is correct, the back plate can be close to the extruder)

5. Insert the screws removed in the first step into the holes on the top of the back panel and screw them in with a screw wrench.

调平教程：

！！！安装千分表前请将热床归零

1安装千分表，调整热床位置。

2.关闭打印机电机（或打印机断电/重启），手动调平不需要用到电机。##拓竹的网床补偿在任何时候都生效，即使只是移动工具头位置##

3.将打印头推到位置1，千分表归零。

4.将打印头推到位置2，调整热床下方的螺丝，直到千分表归零

5.推到位置3执行相同操作。

6.不要强迫症，差不多得了。

Leveling Tutorial:

! ! ! Please reset the heating bed to zero before installing the dial indicator.

1.Install the dial indicator and adjust the position of the hot bed.

2. Turn off the printer motor (or power off/restart the printer). Manual leveling does not require the use of the motor. 

##BAMBULAB X1/P1’s bedmesh is effective at any time, even if you just move the tool head position##

3. Push the print head to position 1 and return the dial indicator to zero.

4. Push the print head to position 2 and adjust the screws under the hot bed until the dial indicator returns to zero.

5. Push to position 3 to perform the same operation.

6. Don’t be obsessive-compulsive, you almost have it.