The mace buddy
The mace buddy is the ideal gadget for all friends of white smoke.
It consists of a base, a V-shaped construction pad and a tamper.
On the base, there is both a filter holder and a leaf holder.
Everything you need for shooting is thus always immediately at hand. In addition, the part also looks quite good on the living room table.
In the package are 2 versions of the mace buddy. The versions differ in the size of the filter holders (7 mm & 9 mm). The two sizes cover virtually all common activated carbon filters on the market - self-rotated filters anyway.
For decoration, there is a nice embossing of a hemp leaf on one side of the base. (Please note the point special requests!).
So that you can connect the V-shaped construction base with the base and the tamper is held, a total of 10 magnets with a size of 5 x 1 mm are needed! For a safe and firm stand, 4 rubber feet with a diameter of 10 mm are also needed at the bottom of the base.
Dimensions complete: 120 mm x 88 mm x 28 mm (length x width X height).
Base
Dimensions: 120 mm x 70 mm x 22 mm (length x width X height).
Sheet thickness up to 5.2 mm.
The base serves both as a filter holder (activated carbon filter with 7 / 9 mm or self-twisted) and as a holder for the leaflets (thickness of the package maximum 5.2 mm). Likewise, the tamper finds its place in the side of the base.
Building pad in V-shape
Dimensions: 110 mm x 54 mm x 24 mm, 35 mm (length x width X height, leg length).
The construction base in V-shape is fixed to the base with magnets and can be conveniently removed to pour the precious scraps into the bag. Thanks to the rubber feet on the base, the mace buddy remains safe and firm in the process.
Stopper
Dimensions: 7 mm Γ, x 90 mm length.
The tamper is also held in the base with a magnet and thus secured against accidentally falling out. On the tamper is the name again in a beautiful embossing, which also makes the tamper more grippy and has a nice feel. Perfect for stuffing the good clubs.
**Special requests
Should you want to have the V-shaped construction pad personalized, write me after the purchase briefly. The embossing of lettering is possible without further ado! (Please specify font type and desired text)
The service is free of charge and included in the purchase price!
I try to process every request as soon as possible!
**Assembly
After printing - Before assembly.
The tamper needs to be sandpapered after printing so that it can slide smoothly into the base without resistance. I recommend first a 320 sandpaper and then a 400 or 600 for a perfect result. Wet sanding is best!
When printing without supports, further sanding is hardly necessary. I only sand the edges a bit, if at all, so everything feels nice and smooth.
When printing with supports and the specified angle of about 45Β°, remove the supports and sand the appropriate surfaces. Again, I recommend a 320 grit sandpaper first and then a 400 or 600 grit for a perfect result. Wet sanding is best!
Rubber feet
The assembly is very simple. Simply attach the 4 rubber feet with a diameter of 10 mm on the floor. There are extra 4 recesses for this purpose.
**Magnets
4 magnets are to be attached to each base and 4 further to the building base. To do this, simply glue a drop of super glue into the recesses for the magnets and a 5 x 1 mm magnet in each case. Please pay attention to the polarity of the individual magnets! This is the only way that the construction pad will hold later and will not be repelled :)
To attach the magnet for the tamper inside the base, first glue the magnet into the tamper and let it dry. Then place a small piece of paper on top of the magnet and place the magnet that is to be glued inside the base. Now place a drop of superglue on the magnet and gently insert the tamper into the base until the tamper is flush with the base (the end of the tamper with the end of the base). Now press well and wait briefly. The paper is used to prevent any adhesive that may ooze out from coming into contact with the magnet on the tamper. Otherwise, it could happen that the tamper sticks inside. The paper may remain stuck inside or fall out over time - the magnet is not affected by this.
**Small tip.
It is best to glue the magnets on one side (base or building pad), place the magnets of the opposite side on the respective magnets and then mark the visible side of the placed magnets with a pen. The marked side is now the one that has to be glued on the opposite side. If you drop the small parts, you are grateful for this mark :)
Shopping list for required components.
10 x magnets, Γ: 5 mm, thickness: 1 mm. (8 for the building pad/base, 2 for the tamper).
4 x rubber feet, 10 mm Γ